tillitis-key/doc/toolchain_setup.md

Toolchain setup

NOTE: Documentation migrated to dev.tillitis.se, this is kept for history. This is likely to be outdated.

Here are instructions for setting up the tools required to build the project. Tested on Ubuntu 22.10.

General development environment

The following is intended to be a complete list of the packages that are required for doing all of the following:

• building and developing TKey device and client apps
• building our QEMU machine (useful for apps dev)
• building and developing firmware and FPGA gateware (which also requires building the toolchain below)

sudo apt install build-essential clang lld llvm bison flex libreadline-dev \
                 gawk tcl-dev libffi-dev git mercurial graphviz \
                 xdot pkg-config python3 libftdi-dev \
                 python3-dev libeigen3-dev \
                 libboost-dev libboost-filesystem-dev \
                 libboost-thread-dev libboost-program-options-dev \
                 libboost-iostreams-dev cmake libusb-1.0-0-dev \
                 ninja-build libglib2.0-dev libpixman-1-dev \
                 golang clang-format \
                 gcc-arm-none-eabi libnewlib-arm-none-eabi \
                 libstdc++-arm-none-eabi-newlib

Device permissions

To allow sudo-less programming, you can install a udev rule that will assign the tkey programmer, and also an unprogrammed CH552, to the dialout group. You will also need to add your user to this group:

sudo cp contrib/99-tillitis.rules /etc/udev/rules.d
sudo udevadm control --reload-rules
sudo usermod -aG dialout ${USER}

To apply the new group, log out and then log back in.

You can check the device permissions to determine if the group was successfully applied. First, use lsusb to find the location of the programmer:

lsusb -d 1209:8886
Bus 001 Device 023: ID 1209:8886 Generic TP-1

Then, you can check the permissions by using the bus and device number reported above. Note that this pair is ephemeral and may change after every device insertion:

ls -l /dev/bus/usb/001/023
crw-rw---- 1 root dialout 189, 22 Feb 16 14:58 /dev/bus/usb/001/023

Gateware: Yosys/Icestorm toolchain

If the LED of your TKey is steady white when you plug it, then the firmware is running and it's already usable! If you want to develop TKey apps, then only the above general development environment is needed.

Compiling and installing Yosys and friends is only needed if your TKey is not already running the required firmware and FPGA gateware, or if you want to do development on these components.

These steps are used to build and install the icestorm toolchain. The binaries are installed in /usr/local. Note that if you have or install other versions of these tools locally, they could conflict (case in point: yosys installed on MacOS using brew).

git clone https://github.com/YosysHQ/icestorm
cd icestorm
git checkout d20a5e9001f46262bf0cef220f1a6943946e421d
make -j$(nproc)
sudo make install
cd ..

# Custom iceprog for the RPi 2040-based programmer (will be upstreamed).
# Note: install dependencies for building tillitis-iceprog on Ubuntu:
# sudo apt install libftdi-dev libusb-1.0-0-dev
git clone -b interfaces https://github.com/tillitis/icestorm tillitis--icestorm
cd tillitis--icestorm/iceprog
make
sudo make PROGRAM_PREFIX=tillitis- install
cd ../..

git clone https://github.com/YosysHQ/yosys
cd yosys
git checkout yosys-0.26
make -j$(nproc)
sudo make install
cd ..

git clone https://github.com/YosysHQ/nextpnr
cd nextpnr
git checkout nextpnr-0.5
cmake -DARCH=ice40 -DCMAKE_INSTALL_PREFIX=/usr/local .
make -j$(nproc)
sudo make install
cd ..

References:

• http://bygone.clairexen.net/icestorm/

Firmware: riscv toolchain

The TKey implements a picorv32 soft core CPU, which is a RISC-V microcontroller with the C instructions and Zmmul extension, multiply without divide (RV32ICZmmul). You can read more about it.

The project uses the LLVM/Clang suite and version 15 or later is required. As of writing Ubuntu 22.10 has version 15 packaged. You may be able to get it installed on older Ubuntu and Debian using the instructions on https://apt.llvm.org/ . There are also binary releases here: https://github.com/llvm/llvm-project/releases

References:

• https://github.com/YosysHQ/picorv32

If your available objcopy and size commands is anything other than the default llvm-objcopy and llvm-size define OBJCOPY and SIZE to whatever they're called on your system before calling make.

CH552 USB to Serial firmware

The USB to Serial firmware runs on the CH552 microcontroller, and provides a USB CDC profile which should work with the default drivers on all major operating systems. MTA1-USB-V1 and TK-1 devices come with the CH552 microcontroller pre-programmed.

Toolchain setup and build instructions for this firmware are detailed in the ch552_fw directory