mirror of
https://github.com/QubesOS/qubes-doc.git
synced 2024-10-01 01:25:40 -04:00
246 lines
10 KiB
Markdown
246 lines
10 KiB
Markdown
---
|
|
layout: doc
|
|
title: Block (Storage) Devices
|
|
permalink: /doc/block-devices/
|
|
redirect_from:
|
|
- /doc/stick-mounting/
|
|
- /en/doc/stick-mounting/
|
|
- /doc/StickMounting/
|
|
- /wiki/StickMounting/
|
|
---
|
|
|
|
# Block (Storage) Devices #
|
|
|
|
*This page is part of [device handling in qubes].*
|
|
|
|
If you don't know what a "block device" is, just think of it as a fancy way to say "something that stores data".
|
|
|
|
|
|
## Using The GUI to Attach a Drive ##
|
|
|
|
(**Note:** In the present context, the term "USB drive" denotes any [USB mass storage device][mass-storage].
|
|
In addition to smaller flash memory sticks, this includes things like USB external hard drives.)
|
|
|
|
Qubes OS supports the ability to attach a USB drive (or just its partitions) to any qube easily, no matter which qube handles the USB controller.
|
|
|
|
Attaching USB drives is integrated into the Devices Widget: ![device manager icon]
|
|
Simply insert your USB drive and click on the widget.
|
|
You will see multiple entries for your USB drive; typically, `sys-usb:sda`, `sys-usb:sda1`, and `sys-usb:2-1` for example.
|
|
Entries starting with a number (e.g. here `2-1`) are the [whole usb-device][USB].
|
|
Entries without a number (e.g. here `sda`) are the whole block-device.
|
|
Other entries are partitions of that block-device (e.r. here `sda1`).
|
|
|
|
The simplest option is to attach the entire block drive.
|
|
In our example, this is `sys-usb:sda`, so hover over it.
|
|
This will pop up a submenu showing running VMs to which the USB drive can be connected.
|
|
Click on one and your USB drive will be attached!
|
|
|
|
**Note:** attaching individual partitions (e.g. `sys-usb:sda1`) can be slightly more secure because it doesn't force the target AppVM to parse the partition table.
|
|
However, it often means the AppVM won't detect the new partition and you will need to manually mount it inside the AppVM.
|
|
See below for more detailed steps.
|
|
|
|
|
|
## Block Devices in VMs ##
|
|
|
|
If not specified otherwise, block devices will show up as `/dev/xvdi*` in a linux VM, where `*` may be the partition-number.
|
|
If a block device isn't automatically mounted after attaching, open a terminal in the VM and execute:
|
|
|
|
cd ~
|
|
mkdir mnt
|
|
sudo mount /dev/xvdi2 mnt
|
|
|
|
where `xvdi2` needs to be replaced with the partition you want to mount.
|
|
This will make your drive content accessible under `~/mnt`.
|
|
|
|
Beware that when you attach a whole block device, partitions can be identified by their trailing integer (i.e. `/dev/xvdi2` for the second partition, `/dev/xvdi` for the whole device), whereas if you attach a single partition, the partition has *no trailing integer*.
|
|
|
|
If several different block-devices are attached to a single VM, the last letter of the device node name is advanced through the alphabet, so after `xvdi` the next device will be named `xvdj`, the next `xvdk`, and so on.
|
|
|
|
To specify this device node name, you need to use the command line tool and its [`frontend-dev`-option][frontend-dev].
|
|
|
|
|
|
## Command Line Tool Guide ##
|
|
|
|
The command-line tool you may use to mount whole USB drives or their partitions is `qvm-block`, a shortcut for `qvm-device block`.
|
|
|
|
`qvm-block` won't recognise your device by any given name, but rather the device-node the sourceVM assigns.
|
|
So make sure you have the drive available in the sourceVM, then list the available block devices (step 1.) to find the corresponding device-node.
|
|
|
|
In case of a USB-drive, make sure it's attached to your computer.
|
|
If you don't see anything that looks like your drive, run `sudo udevadm trigger --action=change` in your USB-qube (typically `sys-usb`)
|
|
|
|
1. In a dom0 console (running as a normal user), list all available block devices:
|
|
|
|
qvm-block
|
|
|
|
This will list all available block devices in your system across all VMs.
|
|
The name of the qube hosting the block device is displayed before the colon in the device ID.
|
|
The string after the colon is the ID of the device used within the qube, like so:
|
|
|
|
sourceVM:sdb Cruzer () 4GiB
|
|
sourceVM:sdb1 Disk () 2GiB
|
|
|
|
2. Assuming your block device is attached to `sys-usb` and its device node is `sdb`, we attach the device to a qube with the name `work` like so:
|
|
|
|
qvm-block attach work sys-usb:sdb
|
|
|
|
This will attach the device to the qube as `/dev/xvdi` if that name is not already taken by another attached device, or `/dev/xvdj`, etc.
|
|
|
|
You may also mount one partition at a time by using the same command with the partition number, e.g. `sdb1`.
|
|
|
|
3. The block device is now attached to the qube.
|
|
If using a default qube, you may open the Nautilus file manager in the qube, and your drive should be visible in the **Devices** panel on the left.
|
|
If you've attached a single partition (e.g. `sdb2` instead of `sdb` in our example), you may need to manually mount before it becomes visible:
|
|
|
|
cd ~
|
|
mkdir mnt
|
|
sudo mount /dev/xvdi mnt
|
|
|
|
|
|
4. When you finish using the block device, click the eject button or right-click and select **Unmount**.
|
|
|
|
If you've manually mounted a single partition in the above step, use:
|
|
|
|
sudo umount mnt
|
|
|
|
5. In a dom0 console, detach the device
|
|
|
|
qvm-block detach work sys-usb:sdb
|
|
|
|
6. You may now remove the device or attach it to another qube.
|
|
|
|
|
|
## Recovering From Premature Device Destruction ##
|
|
|
|
If the you fail to detach the device before it's destroyed in the sourceVM (e.g. by physically detaching the thumbdrive), [there will be problems][premature removal].
|
|
|
|
To recover from this error state, in dom0 run
|
|
|
|
virsh detach-disk targetVM xvdi
|
|
|
|
(where `targetVM` is to be replaced with the VM name you attached the device to and `xvdi` is to be replaced with the used [frontend device node][frontend-dev].)
|
|
|
|
However, if the block device originated in dom0, you will have to refer to the next section.
|
|
|
|
|
|
### What if I removed the device before detaching it from the VM?###
|
|
|
|
Currently (until issue [1082] gets implemented), if you remove the device before detaching it from the qube, Qubes OS (more precisely, `libvirtd`) will think that the device is still attached to the qube and will not allow attaching further devices under the same name.
|
|
The easiest way to recover from such a situation is to reboot the qube to which the device was attached.
|
|
If this isn't an option, you can manually recover from the situation by following these steps:
|
|
|
|
1. Physically connect the device back.
|
|
You can use any device as long as it will be detected under the same name (for example, `sdb`).
|
|
|
|
2. Attach the device manually to the same VM using the `xl block-attach` command.
|
|
It is important to use the same "frontend" device name (by default, `xvdi`).
|
|
You can get it from the `qvm-block` listing:
|
|
|
|
[user@dom0 ~]$ qvm-block
|
|
sys-usb:sda DataTraveler_2.0 () 246 MiB (attached to 'testvm' as 'xvdi')
|
|
[user@dom0 ~]$ sudo xl block-attach testvm phy:/dev/sda backend=sys-usb xvdi
|
|
|
|
In above example, all `xl block-attach` parameters can be deduced from the output of `qvm-block`.
|
|
In order:
|
|
|
|
* `testvm` - name of target qube to which device was attached - listed in brackets by `qvm-block` command
|
|
* `phy:/dev/sda` - physical path at which device appears in source qube (just after source qube name in `qvm-block` output)
|
|
* `backend=sys-usb` - name of source qube, can be omitted in the case of dom0
|
|
* `xvdi` - "frontend" device name (listed at the end of line in `qvm-block` output)
|
|
|
|
3. Now properly detach the device, either using Qubes VM Manager or the `qvm-block -d` command.
|
|
|
|
|
|
## Attaching a File ##
|
|
|
|
To attach a file as block device to another qube, first turn it into a loopback device inside the sourceVM.
|
|
|
|
1. In the linux sourceVM run
|
|
|
|
sudo losetup -f --show /path/to/file
|
|
|
|
[This command][losetup] will create the device node `/dev/loop0` or, if that is already in use, increase the trailing integer until that name is still available.
|
|
Afterwards it prints the device-node-name it found.
|
|
|
|
2. If you want to use the GUI, you're done.
|
|
Click the Device Manager ![device manager icon] and select the `loop0`-device to attach it to another qube.
|
|
|
|
If you rather use the command line, continue:
|
|
|
|
In dom0, run `qvm-block` to display known block devices.
|
|
The newly created loop device should show up:
|
|
|
|
~]$ qvm-block
|
|
BACKEND:DEVID DESCRIPTION USED BY
|
|
sourceVM:loop0 /path/to/file
|
|
|
|
3. Attach the `loop0`-device using qvm-block as usual:
|
|
|
|
qvm-block a targetVM sourceVM:loop0
|
|
|
|
4. After detaching, destroy the loop-device inside the sourceVM as follows:
|
|
|
|
sudo losetup -d /dev/loop0
|
|
|
|
|
|
## Additional Attach Options ##
|
|
|
|
Attaching a block device through the command line offers additional customisation options, specifiable via the `--option`/`-o` option.
|
|
(Yes, confusing wording, there's an [issue for that](https://github.com/QubesOS/qubes-issues/issues/4530).)
|
|
|
|
|
|
### frontend-dev ###
|
|
|
|
This option allows you to specify the name of the device node made available in the targetVM.
|
|
This defaults to `xvdi` or, if already occupied, the first available device node name in alphabetical order.
|
|
(The next one tried will be `xvdj`, then `xvdk`, and so on ...)
|
|
|
|
usage example:
|
|
|
|
qvm-block a work sys-usb:sda1 -o frontend-dev=xvdz
|
|
|
|
This command will attach the partition `sda1` to `work` as `/dev/xvdz`.
|
|
|
|
|
|
### read-only ###
|
|
|
|
Attach device in read-only mode.
|
|
Protects the block device in case you don't trust the targetVM.
|
|
|
|
If the device is a read-only device, this option is forced true.
|
|
|
|
usage example:
|
|
|
|
qvm-block a work sys-usb:sda1 -o read-only=true
|
|
|
|
There exists a shortcut to set read-only `true`, `--ro`:
|
|
|
|
qvm-block a work sys-usb:sda1 --ro
|
|
|
|
The two commands are equivalent.
|
|
|
|
|
|
### devtype ###
|
|
|
|
Usually, a block device is attached as disk.
|
|
In case you need to attach a block device as cdrom, this option allows that.
|
|
|
|
usage example:
|
|
|
|
qvm-block a work sys-usb:sda1 -o devtype=cdrom
|
|
|
|
This option accepts `cdrom` and `disk`, default is `disk`.
|
|
|
|
|
|
|
|
[device handling in qubes]: /doc/device-handling/
|
|
[mass-storage]: https://en.wikipedia.org/wiki/USB_mass_storage_device_class
|
|
[device manager icon]:/attachment/wiki/Devices/media-removable.png
|
|
[frontend-dev]: #frontend-dev
|
|
[premature removal]: https://github.com/QubesOS/qubes-issues/issues/1082
|
|
[detach dom0 device]: /doc/usb/#what-if-i-removed-the-device-before-detaching-it-from-the-vm
|
|
[losetup]: https://linux.die.net/man/8/losetup
|
|
[USB]:/doc/usb-devices/
|
|
[1082]: https://github.com/QubesOS/qubes-issues/issues/1082
|
|
|