portapack-mayhem/README.md
Jared Boone e7c0fa394b PortaPack Sync, take 2 (#215)
* Power: Turn off additional peripheral clock branches.

* Update schematic with new symbol table and KiCad standard symbols.
Fix up wires.

* Schematic: Update power net labels.

* Schematic: Update footprint names to match library changes.

* Schematic: Update header vendor and part numbers.

* Schematic: Specify (arbitrary) value for PDN# net.

* Schematic: Remove fourth fiducial. Not standard practice, and was taking up valuable board space.

* Schematic: Add reference oscillator -- options for clipped sine or HCMOS output.

* Schematic: Update copyright year.

* Schematic: Remove CLKOUT to CPLD. It was a half-baked idea.

* Schematic: Add (experimental) GPS circuit.
Add note about charging circuit.
Update date and revision to match PCB.

* PCB: Update from schematic change: now revision 20180819.
Diff was extensive due to net renumbering...

* PCB: Fix GPS courtyard to accommodate crazy solder paste recommendation in integration manual.
PCB: Address DRC clearance violation between via and oscillator pad.

* PCB: Update copyright on drawing.

* Update schematic and PCB date and revision.

* gitignore: Sublime Text editor project/workspace files

* Power: Power up or power down peripheral clock at appropriate times, so firmware doesn't freeze...

* Clocking: Fix incorrect shift for CGU IDIVx_CTRL.PD field.

* LPC43xx: Add CGU IDIVx struct/union type.

* Power: Switch off unused IDIV dividers. Make note of active IDIVs and their use.

* HackRF Mode: Upgrade firmware to 2018.01.1 (API 1.02)

* MAX V CPLD: Refactor class to look more like Xilinx CoolRunner II CPLD class.

* MAX V CPLD: Add BYPASS, SAMPLE support.
Rename enter_isp -> enable, exit_isp -> disable.
Use SAMPLE at start of flash process, which somehow addresses the problem where CFM wouldn't load into SRAM (and become the active bitstream) after flashing.

* MAX V CPLD: Reverse verify data checking logic to make it a little faster.

* CPLD: After reprogramming flash, immediately clamp I/O signals, load to SRAM, and "execute" the new bitstream.

* Si5351: Refactor code, make one of the registers more type-safe.
Clock Manager: Track selected reference clock source for later use in user interface.

* Clock Manager: Add note about PPM only affecting Si5351C PLLA, which always runs from the HackRF 25MHz crystal.
It is assumed an external clock does not need adjustment, though I am open to being convinced otherwise...

* PPM UI: Show "EXT" when showing PPM adjustment and reference clock is external.

* CPLD: Add pins and logic for new PortaPack hardware feature(s).

* CPLD: Bitstream to support new hardware features.

* Clock Generator: Add a couple more setter methods for ClockControl registers.

* Clock Manager: Use shared MCU CLKIN clock control configuration constant.

* Clock Manager: Reduce MCU CLKIN driver current. 2mA should be plenty.

* Clock Manager: Remove redundant clock generator output enable.

* Bootstrap: Remove unnecessary ldscript hack to locate SPIFI mode change code in RAM.

* Bootstrap: Get CPU operating at max frequency as soon as possible.
Update SPIFI speed comment.
Make some more LPC43xx types into unions with uint32_t.

* Bootstrap: Explicitly configure IDIVB for SPIFI, despite LPC43xx bootloader setting it.

* Clock Manager: Init peripherals before CPLD reconfig. Do the clock generator setup after, so we can check presence of PortaPack reference clock with the help of the latest CPLD bitstream.

* Clock Manager: Reverse sense of conditional that determines crystal or non-crystal reference source. This is for an expected upcoming change where multiple external options can be differentiated.

* Bootstrap: Consolidate clock configuration, update SPIFI rate comment.

* Clock Manager: Use IDIVA for clock source for all peripherals, instead of PLL1. Should make switching easier going forward.
Don't use IRC as clock during initial clock manager configuration. Until we switch to GP_CLKIN, we should go flat out...

* ChibiOS M0: Change default clock speed to 204MHz, since bootstrap now maxes out clock speed before starting M0 execution.

* PortaPack IO: Expose method to set reference oscillator enable pin.

* Pin configuration: Do SPIFI pin config with other pins, in preparation for eliminating separate bootloader.

* Pin configuration: Disable input buffers on pins that are never read.

* Revert "ChibiOS M0: Change default clock speed to 204MHz, since bootstrap now maxes out clock speed before starting M0 execution."

This reverts commit c0e2bb6cc4cc656769323bdbb8ee5a16d2d5bb03.

* PCB: Change PCB stackup, Tg, clarify solder mask color, use more metric.

* PCB: Move HackRF header P9 to B.CrtYd layer.

* PCB: Change a Tg reference I missed.

* PCB: Update footprints for parts with mismatched CAD->tape rotation.
Adjust a few layer choice and line thickness bits.

* PCB: Got cold feet, switched back to rectangular pads.

* PCB: Add Eco layers to be visible and Gerber output.

* PCB: Use aux origin for plotting, for tidier coordinates.

* PCB: Output Gerber job file, because why not?

* Schematic: Correct footprints for two reference-related components.

* Schematic: Remove manfuacturer and part number for DNP component.

* Schematic: Specify resistor value, manufacturer, part number for reference oscillator series termination.

* PCB: Update netlist and footprints from schematic.

* Netlist: Updated component values, footprints.

* PCB: Nudge some components and traces to address DRC clearance violations.

* PCB: Allow KiCad to update zone timestamps (again?!).

* PCB: Generate *all* Gerber layers.

* Schematic, PCB: Update revision to 20181025.

* PCB: Adjust fab layer annotations orientation and font size.

* PCB: Hide mounting hole reference designators on silk layer.

* PCB: Shrink U1, U3 pads to get 0.2mm space between pads.

* PCB: Set pad-to-mask clearance to zero, leave up to fab. Set minimum mask web to 0.2mm for non-black options.

* PCB: Revise U1 pad shape, mask, paste, thermal drills.
Clearance is improved at corner pads.

* PCB: Tweak U3 for better thermal pad/drill/mask/paste design.

* PCB: Change solder mask color to blue.

* Schematic, PCB: Update revision to 20181029.

* PCB: Bump minimum mask web down a tiny bit because KiCad is having trouble with math.

* Update schematic

* Remove unused board files.

* Add LPC43xx functions.

* chibios: Replace code with per-peripheral structs defining clocks, interrupts, and reset bits.

* LPC43xx: Add MCPWM peripheral struct.

* clock generator: Use recommended PLL reset register value.

Datasheet recommends a value. AN619 is quiet on the topic, claims the low nibble is default 0b0000.

* GPIO: Tweak masking of SCU function.

I don't remember why I thought this was necessary...

* HAL: Explicitly turn on timer peripheral clocks used as systicks, during init.

* SCU: Add struct to hold pin configuration.

* PAL: Add functions to address The Glitch.

https://greatscottgadgets.com/2018/02-28-we-fixed-the-glitch/

* PAL/board: New IO initialization code

Declare initial state for SCU pin config, GPIOs. Apply initial state during PAL init. Perform VAA slow turn-on to address The Glitch.

* Merge M0 and M4 to eliminate need for bootstrap firmware

During _early_init, detect if we're running on the M4 or M0.
If M4: do M4-specific core initialization, reset peripherals, speed up SPIFI clock, start M0, go to sleep.
If M0: do all the other things.

* Pins: Miscellaneous SCU configuration tweaks.

* Little code clarity improvement.

* bootstrap: Remove, not necessary.

* Clock Manager: Large re-working to support external references.

* Clock Manager: Actually store chosen clock reference

Similarly-named local was covering a member and discarding the value.

* Clock Manager: Reference type which contains source, frequency.

* Setup: Display reference source, frequency in frequency correction screen.

* LPC43xx API: Add extern "C" for use from C++.

* Use LPC43xx API for SGPIO, GPDMA, I2S initialization.

* I2S: Add BASE_AUDIO_CLK management.

* Add MOTOCON_PWM clock/reset structure.

* Serial: Fix dumb typos.

* Serial: Remove extra reference operator.

* Serial: Cut-and-paste error in structure type name.

* Move SCU structure from PAL to LPC43xx API.

It'd be nice if I gave some thought to where code should live before I commit it.

* VAA power: Move code to HackRF board file

It doesn't belong in PAL.

* MAX5 CPLD: Add SAMPLE and EXTEST methods.

* Flash image: Change packing scheme to use flash more efficiently.

Application is now a single image for both M4 bootstrap and M0.
Baseband images come immediately after application binary. No need to align to large blocks (and waste lots of flash).

* Clock Manager: Remove PLL1 power down function.

* Move and rename peripherals reset function to board module.

* Remove unused peripheral/clock management.

* Clock Manager: Extract switch to IRC into separate function.

* Clock Manager: More explicit shutdown of clocks, clock generator.

* Move initialization to board module.

* ChibiOS: Rename "application" board, add "baseband" board.

There are now two ChibiOS "boards", one which runs the application and does the hardware setup. The other board, "baseband", does very little setup.

* Clock Manager: Remove unused crystal enable/disable code.

* Clock Manager: Restore clock configuration to SPIFI bootloader state before app shutdown.

* Reset peripherals on app shutdown.

Be careful not to reset M0APP (the core we're running on) or GPIO (which is holding the hardware in a stable state).

* M4/baseband hal_lld_init: use IDIVA, which is configured earlier by M0.

This was causing problems during restart into HackRF mode. Baseband hal_lld_init changed M4 clock from IDIVA (set by M0) to PLL1, which was unceremoniously turned off during shutdown.

* Audio app: Stop audio PLL on shutdown.

* M4 HAL: Make LPC43XX_M4_CLK_SRC optional.

This was changing the BASE_M4_CLK when a baseband was run.

* LPC43xx C++ layer: Fix IDIVx constructor IDIV narrow field width.

* Application board: hide the peripherals_reset function, as it isn't useful except during hardware init.

* Consolidate hardware init code to some degree.

ClockManager is super-overloaded and murky in its purpose.
Migrate audio from IDIVC to IDIVD, to more closely resemble initial clock scheme, so it's simpler to get back to it during shutdown.

* Migrate some startup code to application board.

* Si5351: Use correct methods for reset().

update_output_enable_control() doesn't reset the enabled outputs to the reset state, unless the object is freshly initialized, which it isn't when performing firmware shutdown.
For similar reasons, use set_clock_control() instead of setting internal state and then using the update function.

* GPIO: Set SPIFI CS pin to match input buffer state coming out of bootloader.

* Change application board.c to .cpp, with required dependent changes

* Board: Clean up SCU configuration code/data.

* I2S: Add shutdown code and use it.

* LPC43xx: Consolidate a bunch of structures that had been scattered all over.

...because I'm an undisciplined coder.

* I2S: Fix ordering of branch and base clock disable.

Core was hanging, presumably because the register interface on the branch/peripheral was unresponsive after the base clock was disabled.

* Controls: Save and expose raw navigation wheel switch state

I need to do some work on debouncing and ignoring simultaneous key presses.

* Controls: Add debug view for switches state.

* Controls: Ignore all key presses until all keys are released.

This should address some mechanical quirks of the navigation wheel used on the PortaPack.

* Clock Manager: Wait for only the necessary PLL to lock.

Wasn't working on PortaPacks without a built-in clock reference, as that uses the other PLL.
TODO: Switching PLLs may be kind of pointless now...

* CMake: Pull HackRF project from GitHub and build.

* CMake: Remove commented code.

* CMake: Clone HackRF via HTTPS, not SSH.

* CMake: Extra pause for slow post-DFU firmware boot-up.

* CMake: TODO to fix SVF/XSVF file source.

* CMake: Ask HackRF hackrf_usb to make DFU binary.

* Travis-CI: Add dfu-util, now that HackRF firmware is being built for inclusion.

* Travis-CI: Update build environment to Ubuntu xenial

Previously Trusty.

* Travis-CI: Incorrectly structured my request for dfu-util package.

I'm soooo talented.

* ldscript: Mark flash, ram with correct R/W/X flags.

* ldscript: Enlarge M0 flash region to 1Mbyte, the size of the HackRF SPI flash.

* Receiver: Hide PPM adjustment if clock source is not HackRF crystal.

* Documentation: Update product photos and README.

* Documentation: Add TCXO feature to README description.

* Application: Rearrange files to match HAVOC directory structure.

* Map view in AIS (#213)

* Added GeoMapView to AISRecentEntryDetailView

* Added autoupdate in AIS map

* Revert "Map view in AIS (#213)"

This reverts commit 262c030224.

This commit will be cherry-picked onto a clean branch, then re-committed after a troublesome pull request is reverted.

* Revert "Upstream merge to make new revision of PortaPack work (#206)"

This reverts commit 920b98f7c9.

This pull request was missing some changes and was preventing firmware from functioning on older PortaPacks.

* CPLD: Pull bitstream from HackRF project.

* SGPIO: Identify pins on CPLD by their new functions. Pull down HOST_SYNC_EN.

* CPLD: Don't load HackRF CPLD bitstream into RAM.

Trying to converge CPLD implementations, so this shouldn't be necesssary. HOWEVER, it would be good to *check* the CPLD contents and provide a way to update, if necessary.

* CPLD: Tweak clock generator config to match CPLD timing changes in HackRF.

* PinConfig: Drive CPLD pins correctly.

* CMake: Use jboone/hackrf master branch, now that CPLD fixes are there.

* CMake: Fix HackRF CPLD SVF dependency.

Build would break on the first pass, but work if you restarted make.

* CMake: Fix my misuse of the HackRF CMake configuration -- was building from too deep in the directory tree

* CMake: Work-around for CMake 3.5 not supporting ExternalProject_Add SOURCE_SUBDIR.

* CMake: Choose a CMP0005 policy to quiet CMake warnings.

* Settings: Show active clock reference. Only show PPM adjustment for HackRF source.

* Radio Settings: Change reference clock text color.

Make consistent color with other un-editable text.
TODO: This is a bit of a hack to get ui::Text objects to support custom colors, like the Label structures used elsewhere.
2019-02-03 18:25:11 +00:00

5.1 KiB

HAVOC banner

HAVOC is a fork of the PortaPack H1 firmware, a portability add-on for the HackRF One software-defined radio.

Hardware is available at ShareBrained Technology.

It is build on top of ShareBrained's firmware, meaning that the original functionalities are kept (except when I don't sync for 2 months).

Documentation

READ THE WIKI

If you want to submit a bug report, suggest something... Don't hesitate, use this page: https://github.com/furrtek/portapack-havoc/issues (Check the progress list below first).

Summary

As its name implies, HAVOC's functionalities can be fun, mean and even useful sometimes. You shouldn't use them. No ! Bad ! Put it down.

In most countries, radio transmissions are tightly regulated. Transmitting outside of free/public bands without a licence or authorization, even at very low power, is certainly forbidden where you live. Always bear that in mind. You're the ONLY ONE responsible for what you do with this software.

Fork features

  • IQ file replay
  • Microphone FM transmit with CTCSS
  • CTCSS decoder
  • Frequency manager (save & load from SD card, with categories and notes)
  • File manager
  • "Soundboard" wave file player (put 8-bit mono files in SD card /wav directory)
  • ADS-B receiver with map view
  • ADS-B transmitter (aircraft spoof)
  • SSTV transmitter
  • Fully configurable jammer
  • POCSAG transmitter
  • POCSAG receiver/decoder
  • Morse transmitter (FM tone and CW)
  • OOK transmitter for common remote encoders (PT2262, doorbells, remote outlets, some garage doors, ...)
  • RDS (Radio Data System) PSN, RadioText and Time groups transmitter
  • Meteorological radiosonde receiver for M10 and M2K2...
  • AFSK receiver
  • AFSK transmitter (Bell202...)
  • Nuoptix DTMF sync transmitter (quite specific but can be useful in some theme parks :) )
  • TouchTunes jukebox universal remote (by Notpike)
  • LCR (Language de Commande Routier) message generator
  • Street lighting control transmitter (CCIR tones)
  • "Play Dead" in case of emergency
  • Fully configurable RF signal generator
  • RSSI audio output as pitch (for direction finding)

Progress

Feature Progress Notes
POCSAG RX   95% Needs support for numeric messages
Morse TX 95% Needs fox hunt scheduler and live keying mode
Mic. TX 95% Carrier leak bug, need to find guard tones for various brands of wireless mics
ADS-B RX 90% Needs angle and speed decoding
Close-Call™ 85% Needs adjustments and optimization for wider frequency range
ADS-B TX 85% Works but baseband module needs cleaning
SSTV TX 80% Needs better bitmap file handling, support for other modes (ROBOT ?) and callsign FSK ID
Radiosondes 75% Needs support for other models
Wave visualizer 70% Needs cleaning and handling of other sample formats, high priority
AFSK RX 70% Needs work regarding flexibility
Sigfox RX 40% Tuning basics done, needs decoding code and testing
Generic TXs 30% Raw AX.25, AFSK, FSK, CCIR, DTMF... Tonesets are ready
CC1101 TRX 10% And other sub-GHz transceiver chips like SI4032...
SSTV RX 0%
Scanner 0% Easy, could be used with POCSAG RX to catch jumping channels
SSB TX 0% Requested but math is hard :(
OOK RX 0% See if rtl_433's author is fine with using protocol defs
Analog TV TX 0% Enough CPU ? B&W and no sound ?
LoJack RX 0% Basically AFSK RX
DMR info RX 0% Retrieve DMR channel info. No voice because of vocoder complexity and possible legal issue
Tetra info? 0% Same

Screenshots

HAVOC screenshots

Thanks

  • Sig and cLx for research on AFSK LCR, Xylos, and for lending remote-controlled outlets
  • Pyr3x, Rainer Matla and DC1RDB for the donations :)
  • Keld Norman and Giorgio Campiotti for ideas and suggestions

License

Except where specified in subdirectories of this project, all work is offered under the following license:

Copyright (C) 2013-2019 Jared Boone, ShareBrained Technology, Inc.

Copyright (C) 2015-2016 Furrtek

This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.

Contact

Original firmware and hardware

Jared Boone jared@sharebrained.com

ShareBrained Technology, Inc.

http://www.sharebrained.com/

The latest version of this repository can be found at https://github.com/sharebrained/portapack-hackrf/

HAVOC specific things

Furrtek furrtek@gmail.com

http://www.furrtek.org