Git-Mirrors/tillitis-key
1
0
Fork 0
mirror of https://github.com/tillitis/tillitis-key1.git synced 2024-10-01 01:45:38 -04:00
Code Issues Packages Projects Releases Wiki Activity
fddfd88db2
tillitis-key/doc/system_description/software.md
Joachim Strömbergson dbb7e61509
Add description of exe monitor API 
Signed-off-by: Joachim Strömbergson <joachim@assured.se>
2023-03-22 15:55:36 +01:00

536 lines
22 KiB
Markdown
Raw Blame History

# Tillitis TKey software
## Definitions
* Firmware - software in ROM responsible for loading applications.
The firmware is included as part of the FPGA bit stream.
* Application - software supplied by the host machine, which is
received, loaded, and measured by the firmware (by hashing a
digest over the binary).
Learn more about the concepts in the
[system_description.md](system_description.md).
## CPU
We use a PicoRV32, a 32-bit RISC-V system (RV32ICZmmul), as the CPU
for running the firmware and the loaded app. The firmware and device
app both run in machine mode. All types are little-endian.
## Constraints
The application FPGA is a Lattice ICE40 UP5K, with the following
specifications:
* 30 EBR[^1] x 4 Kbit => 120 Kbit. PicoRV32 uses ~4 EBRs internally
=> 13 KB for Firmware. As of this writing firmware uses 2998 bytes.
* 4 SPRAM[^2] x 32 KB => 128 KB RAM for application/software
[^1]: Embedded Block RAM (also BRAM) residing in the FPGA, can
be configured as RAM or ROM.
[^2]: Single Port RAM (also SRAM).
## Introduction
The TKey has two modes of operation; firmware/loader mode and
application mode. The firmware mode has the responsibility of
receiving, measuring, loading, and starting the application.
The firmware and application uses a memory mapped IO for SoC
communication. This MMIO resides at `0xc000_0000`. *Nota bene*: Almost
all access to MMIO should be word (32 bit) aligned. See table below.
The application has a constrained variant of the firmware memory map,
which is outlined below. E.g. UDS isn't readable, and the `APP_{ADDR,
SIZE}` are not writable for the application.
The firmware (and optionally all software) on the TKey communicates to
the host via the `UART_{RX,TX}_{STATUS,DATA}` registers, using the
framing protocol described in [Framing
Protocol](../framing_protocol/framing_protocol.md).
The firmware defines a protocol (command/response interface) on top of
this framing layer which is used to bootstrap the application onto the
device. All commands are initiated by the host. All commands receive a
reply.
Applications define their own per-application protocol used for
communication with their host part. They may or may not be based on
the Framing Protocol.
## Firmware
The purpose of the firmware is to bootstrap and measure an
application.
The TKey has 128 KB RAM. Firmware loads the app at the start of RAM.
The current C runtime (crt0.S) of apps in our [apps
repo](https://github.com/tillitis/tillitis-key1-apps) sets up the
stack to start just below the end of RAM. This means that a larger app
comes at the compromise of it having a smaller stack.
The firmware is part of FPGA bitstream (ROM), and is loaded at
`0x0000_0000`.
When the firmware starts it clears all RAM and then wait for commands
coming in on `UART_RX`.
Typical use scenario:
1. The host sends the `FW_CMD_LOAD_APP` command with the size of the
device app and the user-supplied secret as arguments and and gets
a `FW_RSP_LOAD_APP` back. After using this it's not possible to
restart the loading of a device app.
2. If the the host receive a sucessful response, it will send
multiple `FW_CMD_LOAD_APP_DATA` commands, together containing the
full application.
3. On receiving`FW_CMD_LOAD_APP_DATA` commands the firmware places
the data into `0x4000_7000` and upwards. The firmware replies
with a `FW_RSP_LOAD_APP_DATA` response to the host for each
received block except the last data block.
4. When the final block of the application image is received with a
`FW_CMD_LOAD_APP_DATA`, the firmware measure the application by
computing a BLAKE2s digest over the entire application. Then
firmware send back the `FW_RSP_LOAD_APP_DATA_READY` response
containing the measurement.
5. The Compound Device Identifier (CDI) is then computed by using
the `UDS`, the measurement of the application, and the `USS`, and
placed in the `CDI` register. Then the start address of the
device app, `0x4000_7000`, is written to `APP_ADDR` and the size
to `APP_SIZE` to let the device application know where it is
loaded and how large it is, if it wants to relocate in RAM.
6. The firmware now starts the application by switching to
application mode by writing to the `SWITCH_APP` register. In this
mode the MMIO region is restricted; e.g. some registers are
removed (`UDS`), and some are switched from read/write to
read-only. This is outlined in the memory map below.
The firmware now executes assembler code that writes zeros to
stack and data of the firmware, then jumps to what's in
`APP_ADDR` which starts device app execution.
There is now no other means of getting back from application mode
to firmware mode than resetting/power cycling the device.
### Developing firmware
Standing in `hw/application_fpga/` you can run `make firmware.elf` to
build just the firmware. You don't need all the FPGA development tools
mentioned in [Toolchain setup](../toolchain_setup.md).
You need Clang with 32 RISC-V support `-march=rv32iczmmul` which comes
in Clang 15. If you don't have version 15 you might get by with
`-march=rv32imc` but things will break if you ever cause it to emit
`div` instructions.
If your available `objcopy` and `size` commands is anything other than
the default `llvm-objcopy` and `llvm-size` define `OBJCOPY` and `SIZE`
to whatever they're called on your system before calling `make
firmware.elf`.
If you want to use our emulator, clone the `tk1` branch of [our
version of qemu](https://github.com/tillitis/qemu) and build:
```
$ git clone -b tk1 https://github.com/tillitis/qemu
$ mkdir qemu/build
$ cd qemu/build
$ ../configure --target-list=riscv32-softmmu --disable-werror
$ make -j $(nproc)
```
(Built with warnings-as-errors disabled, see [this
issue](https://github.com/tillitis/qemu/issues/3).)
Run it like this:
```
$ /path/to/qemu/build/qemu-system-riscv32 -nographic -M tk1,fifo=chrid -bios firmware.elf \
-chardev pty,id=chrid
```
This attaches the FIFO to a tty, something like `/dev/pts/16` which
you can use with host software to talk to the firmware.
To quit QEMU you can use: `Ctrl-a x` (see `Ctrl-a ?` for other commands).
Debugging? Use the HTIF console by removing `-DNOCONSOLE` from the
`CFLAGS` and using the helper functions in `lib.c` like `htif_puts()`
`htif_putinthex()` `htif_hexdump()` and friends for printf-like
debugging.
You can also use the qemu monitor for debugging, e.g. `info
registers`, or run qemu with `-d in_asm` or `-d trace:riscv_trap`.
### Reset
The PicoRV32 starts executing at `0x0000_0000`. Our firmware starts at
`_start` from `start.S` which initializes the `.data`, and `.bss` at
`0x4000_0000` and upwards. A stack is also initialized, starting at
0x4000_6ff0 and downwards. When the initialization is finished, the
firmware waits for incoming commands from the host, by busy-polling
the `UART_RX_{STATUS,DATA}` registers. When a complete command is
read, the firmware executes the command.
### Firmware state machine
States:
- `initial` - At start.
- `loading` - Expect app data.
- `run` - Computes CDI and starts the device app.
- `fail` - Stops waiting for commands, flashes LED forever.
Commands in state `initial`:
| *command* | *next state* |
|-----------------------|--------------|
| `FW_CMD_NAME_VERSION` | unchanged |
| `FW_CMD_GET_UDI` | unchanged |
| `FW_CMD_LOAD_APP` | `loading` |
| | |
Commands in state `loading`:
| *command* | *next state* |
|------------------------|----------------------------------|
| `FW_CMD_NAME_VERSION` | unchanged |
| `FW_CMD_GET_UDI` | unchanged |
| `FW_CMD_LOAD_APP_DATA` | unchanged or `run` on last chunk |
See below for firmware protocol definition.
### User-supplied Secret (USS)
USS is a 32 bytes long secret provided by the user. Typically a host
program gets a passphrase from the user and then does KDF of some
sort, for instance a BLAKE2s, to get 32 bytes which it sends to the
firmware to be part of the CDI computation.
### Compound Device Identifier (CDI) computation
The CDI is computed by:
```
CDI = blake2s(UDS, blake2s(app), USS)
```
In an ideal world, software would never be able to read UDS at all and
we would have a BLAKE2s function in hardware that would be the only
thing able to read the UDS. Unfortunately, we couldn't fit a BLAKE2s
implementation in the FPGA at this time.
The firmware instead does the CDI computation using the special
firmware-only `FW_RAM` which is invisible after switching to app mode.
The `blake2s()` function in the firmware is fed with a buffer in
`FW_RAM` containing the UDS, the app digest, and the USS. It is also
fed with a context used for computations that is also part of the
`FW_RAM`.
After doing the computation `FW_RAM` is also cleared with zeroes.
### Firmware protocol definition
The firmware commands and responses are built on top of the [Framing
Protocol](../framing_protocol/framing_protocol.md).
The commands look like this:
| *name* | *size (bytes)* | *comment* |
|------------------|----------------|------------------------------------------|
| Header | 1 | Framing protocol header including length |
| | | of the rest of the frame |
| Command/Response | 1 | Any of the below commands or responses |
| Data | n | Any additional data |
The responses might include a one byte status field where 0 is
`STATUS_OK` and 1 is `STATUS_BAD`.
Note that the integer types are little-endian (LE).
#### `FW_CMD_NAME_VERSION` (0x01)
Get the name and version of the stick.
#### `FW_RSP_NAME_VERSION` (0x02)
| *name* | *size (bytes)* | *comment* |
|---------|----------------|----------------------|
| name0 | 4 | ASCII |
| name1 | 4 | ASCII |
| version | 4 | Integer version (LE) |
In a bad response the fields will be zeroed.
#### `FW_CMD_LOAD_APP` (0x03)
| *name* | *size (bytes)* | *comment* |
|--------------|----------------|---------------------|
| size | 4 | Integer (LE) |
| uss-provided | 1 | 0 = false, 1 = true |
| uss | 32 | Ignored if above 0 |
Start an application loading session by setting the size of the
expected device application and a user-supplied secret, if
`uss-provided` is 1. Otherwise `USS` is ignored.
#### `FW_RSP_LOAD_APP` (0x04)
Response to `FW_CMD_LOAD_APP`
| *name* | *size (bytes)* | *comment* |
|--------|----------------|-----------------------------|
| status | 1 | `STATUS_OK` or `STATUS_BAD` |
#### `FW_CMD_LOAD_APP_DATA` (0x05)
| *name* | *size (bytes)* | *comment* |
|--------|----------------|---------------------|
| data | 511 | Raw binary app data |
Load 511 bytes of raw app binary into device RAM. Should be sent
consecutively over the complete raw binary. (512 == largest frame
length minus the command byte).
#### `FW_RSP_LOAD_APP_DATA` (0x06)
Response to all but the ultimate `FW_CMD_LOAD_APP_DATA` commands.
| *name* | *size (bytes)* | *comment* |
|--------|----------------|--------------------------|
| status | 1 | `STATUS_OK`/`STATUS_BAD` |
#### `FW_RSP_LOAD_APP_DATA_READY` (0x07)
The response to the last `FW_CMD_LOAD_APP_DATA` is an
`FW_RSP_LOAD_APP_DATA_READY` with the un-keyed hash digest for the
application that was loaded. It allows the host to verify that the
application was correctly loaded. This means that the CDI calculated
will be correct given that the UDS has not been modified.
| *name* | *size (bytes)* | *comment* |
|--------|----------------|--------------------------|
| status | 1 | `STATUS_OK`/`STATUS_BAD` |
| digest | 32 | BLAKE2s(app) |
#### `FW_CMD_GET_UDI` (0x08)
Ask for the Unique Device Identifier (UDI) of the device.
#### `FW_RSP_GET_UDI` (0x09)
Response to `FW_CMD_GET_UDI`.
| *name* | *size (bytes)* | *comment* |
|--------|----------------|-----------------------------------------------------|
| status | 1 | `STATUS_OK`/`STATUS_BAD` |
| udi | 4 | Integer (LE) with Reserved (4 bit), Vendor (2 byte),|
| | | Product ID (6 bit), Product Revision (6 bit) |
| udi | 4 | Integer serial number (LE) |
#### Get the name and version of the device
```
host ->
u8 CMD[1 + 1];
CMD[0].len = 1 // command frame format
CMD[1] = 0x01 // FW_CMD_NAME_VERSION
host <-
u8 RSP[1 + 32]
RSP[0].len = 32 // command frame format
RSP[1] = 0x02 // FW_RSP_NAME_VERSION
RSP[2..6] = NAME0
RSP[6..10] = NAME1
RSP[10..14] = VERSION
RSP[14..] = 0
```
#### Load an application
```
host ->
u8 CMD[1 + 512];
CMD[0].len = 512 // command frame format
CMD[1] = 0x03 // FW_CMD_LOAD_APP
CMD[2..6] = APP_SIZE
CMD[6] = USS supplied? 0 = false, 1 = true
CMD[7..39] = USS
CMD[40..] = 0
host <-
u8 RSP[1 + 4];
RSP[0].len = 4 // command frame format
RSP[1] = 0x04 // FW_RSP_LOAD_APP
RSP[2] = STATUS
RSP[3..] = 0
repeat ceil(APP_SIZE / 511) times:
host ->
u8 CMD[1 + 512];
CMD[0].len = 512 // command frame format
CMD[1] = 0x05 // FW_CMD_LOAD_APP_DATA
CMD[2..] = APP_DATA (511 bytes of app data, pad with zeros)
host <-
u8 RSP[1 + 4]
RSP[0].len = 4 // command frame format
RSP[1] = 0x06 // FW_RSP_LOAD_APP_DATA
RSP[2] = STATUS
RSP[3..] = 0
```
Except response from last chunk of app data which is:
```
host <-
u8 RSP[1 + 512]
RSP[0].len = 512 // command frame format
RSP[1] = 0x07 // FW_RSP_LOAD_APP_DATA_READY
RSP[2] = STATUS
RSP[3..35] = app digest
RSP[36..] = 0
```
### Firmware services
The firmware exposes a BLAKE2s function through a function pointer
located in MMIO `BLAKE2S` (see memory map below) with the with
function signature:
```c
int blake2s(void *out, unsigned long outlen, const void *key,
unsigned long keylen, const void *in, unsigned long inlen,
blake2s_ctx *ctx);
```
where `blake2s_ctx` is:
```c
typedef struct {
uint8_t b[64]; // input buffer
uint32_t h[8]; // chained state
uint32_t t[2]; // total number of bytes
size_t c; // pointer for b[]
size_t outlen; // digest size
} blake2s_ctx;
```
The `libcommon` library in
[tillitis-key1-apps](https://github.com/tillitis/tillitis-key1-apps/)
has a wrapper for using this function.
## Memory map
Assigned top level prefixes:
| *name* | *prefix* | *address length* |
|----------|----------|--------------------------------------|
| ROM | 0b00 | 30 bit address |
| RAM | 0b01 | 30 bit address |
| reserved | 0b10 | |
| MMIO | 0b11 | 6 bits for core select, 24 bits rest |
Addressing:
```
31st bit 0th bit
v v
0000 0000 0000 0000 0000 0000 0000 0000
- Bits [31 .. 30] (2 bits): Top level prefix (described above)
- Bits [29 .. 24] (6 bits): Core select. We want to support at least 16 cores
- Bits [23 .. 0] (24 bits): Memory/in-core address.
```
The memory exposes SoC functionality to the software when in firmware
mode. It is a set of memory mapped registers (MMIO), starting at base
address `0xc000_0000`. For specific offsets/bitmasks, see the file
[tk1_mem.h](../../hw/application_fpga/fw/tk1_mem.h) (in this repo).
Assigned core prefixes:
| *name* | *prefix* |
|--------|----------|
| ROM | 0x00 |
| RAM | 0x40 |
| TRNG | 0xc0 |
| TIMER | 0xc1 |
| UDS | 0xc2 |
| UART | 0xc3 |
| TOUCH | 0xc4 |
| FW_RAM | 0xd0 |
| TK1 | 0xff |
*Nota bene*: MMIO accesses should be 32 bit wide, e.g use `lw` and
`sw`. Exceptions are `FW_RAM` and `QEMU_DEBUG`.
| *name* | *fw* | *app* | *size* | *type* | *content* | *description* |
|-------------------|-------|-----------|--------|----------|-----------|-------------------------------------------------------------------------|
| `TRNG_STATUS` | r | r | | | | TRNG_STATUS_READY_BIT is 1 when an entropy word is available. |
| `TRNG_ENTROPY` | r | r | 4B | u32 | | Entropy word. Reading a word will clear status. |
| `TIMER_CTRL` | r/w | r/w | | | | If TIMER_STATUS_RUNNING_BIT in TIMER_STATUS is 0, setting |
| | | | | | | TIMER_CTRL_START_BIT here starts the timer. |
| | | | | | | If TIMER_STATUS_RUNNING_BIT in TIMER_STATUS is 1, setting |
| | | | | | | TIMER_CTRL_STOP_BIT here stops the timer. |
| `TIMER_STATUS` | r | r | | | | TIMER_STATUS_RUNNING_BIT is 1 when the timer is running. |
| `TIMER_PRESCALER` | r/w | r/w | 4B | | | Prescaler init value. Write blocked when running. |
| `TIMER_TIMER` | r/w | r/w | 4B | | | Timer init or current value while running. Write blocked when running. |
| `UDS_FIRST` | r[^3] | invisible | 4B | u8[32] | | First word of Unique Device Secret key. |
| `UDS_LAST` | | invisible | | | | The last word of the UDS |
| `UART_BITRATE` | r/w | | | | | TBD |
| `UART_DATABITS` | r/w | | | | | TBD |
| `UART_STOPBITS` | r/w | | | | | TBD |
| `UART_RX_STATUS` | r | r | 1B | u8 | | Non-zero when there is data to read |
| `UART_RX_DATA` | r | r | 1B | u8 | | Data to read. Only LSB contains data |
| `UART_RX_BYTES` | r | r | 4B | u32 | | Number of bytes received from the host and not yet read by SW, FW. |
| `UART_TX_STATUS` | r | r | 1B | u8 | | Non-zero when it's OK to write data |
| `UART_TX_DATA` | w | w | 1B | u8 | | Data to send. Only LSB contains data |
| `TOUCH_STATUS` | r/w | r/w | | | | TOUCH_STATUS_EVENT_BIT is 1 when touched. After detecting a touch |
| | | | | | | event (reading a 1), write anything here to acknowledge it. |
| `FW_RAM` | r/w | invisible | 2 kiB | u8[2048] | | Firmware-only RAM. |
| `UDI` | r | invisible | 8B | u64 | | Unique Device ID (UDI). |
| `QEMU_DEBUG` | w | w | | u8 | | Debug console (only in QEMU) |
| `NAME0` | r | r | 4B | char[4] | "tk1 " | ID of core/stick |
| `NAME1` | r | r | 4B | char[4] | "mkdf" | ID of core/stick |
| `VERSION` | r | r | 4B | u32 | 1 | Current version. |
| `SWITCH_APP` | r/w | r | 1B | u8 | | Write anything here to trigger the switch to application mode. Reading |
| | | | | | | returns 0 if device is in firmware mode, 0xffffffff if in app mode. |
| `LED` | r/w | r/w | 1B | u8 | | Control of the color LEDs in RBG LED on the board. |
| | | | | | | Bit 0 is Blue, bit 1 is Green, and bit 2 is Red LED. |
| `GPIO` | r/w | r/w | 1B | u8 | | Bits 0 and 1 contain the input level of GPIO 1 and 2. |
| | | | | u8 | | Bits 3 and 4 store the output level of GPIO 3 and 4. |
| `APP_ADDR` | r/w | r | 4B | u32 | | Firmware stores app load address here, so app can read its own location |
| `APP_SIZE` | r/w | r | 4B | u32 | | Firmware stores app app size here, so app can read its own size |
| `BLAKE2S` | r/w | r | 4B | u32 | | Function pointer to a BLAKE2S function in the firmware |
| `CDI_FIRST` | r/w | r | 32B | u8[32] | | Compound Device Identifier (CDI). UDS+measurement... |
| `CDI_LAST` | | r | | | | Last word of CDI |
| `RAM_ASLR` | w | invisible | 4B | u32 | | Address Space Randomization seed value for the RAM |
| `RAM_SCRAMBLE` | w | invisible | 4B | u32 | | Data scrambling seed value for the RAM |
| `CPU_MON_CTRL` | w | w | 4B | u32 | | Bit 0 enables CPU execution monitor. Can't be unset. Lock adresses |
| `CPU_MON_FIRST` | w | w | 4B | u32 | | First address of the area monitored for execution attempts |
| `CPU_MON_LAST` | w | w | 4B | u32 | | Last address of the area monitored for execution attempts |
[^3]: The UDS can only be read *once* per power-cycle.
Reference in New Issue View Git Blame Copy Permalink