mirror of
https://github.com/tillitis/tillitis-key1.git
synced 2024-10-01 01:45:38 -04:00
90 lines
3.6 KiB
Markdown
90 lines
3.6 KiB
Markdown
|
|
This document describes how to build the FPGA bitstream, including the
|
|
firmware, and get this programmed onto the flash memory of the
|
|
Tillitis Key 1 USB device.
|
|
|
|
The Tillitis Key 1 kit includes:
|
|
|
|
- Tillitis Key 1 USB stick with USB-C plug, marked MTA1-USB V1
|
|
- Programmer board based on Raspberry Pi Pico, with a white holder/jig
|
|
- USB cable with micro-B plug, for connecting the programmer to
|
|
computer
|
|
- USB-C extension cable
|
|
- USB-C to USB-A adapter
|
|
|
|
# Programming FPGA bitstream and firmware onto Tillitis Key 1
|
|
|
|
Connect the programmer to the computer using the USB cable with
|
|
micro-B plug.
|
|
|
|
Place the Tillitis Key 1 (the USB stick) correctly in the programming
|
|
jig and close the hatch.
|
|
|
|
The USB stick can remain in the jig during repeated development,
|
|
programming and testing cycles. The USB stick should then be connected
|
|
to the computer using the provided USB-C cable (use the USB-C-to-A
|
|
adapter if needed). The jig also has a cutout to allow touching where
|
|
the touch sensor is located (next to the LED). Note that connecting
|
|
the USB stick to the computer is not required for programming it. Note
|
|
also that with this setup, to reset the USB stick back to firmware
|
|
mode after loading an app, you need to unplug both the USB cable to
|
|
the stick and the one to the programmer.
|
|
|
|
On Linux, `lsusb` should list the connected programmer as `cafe:4004
|
|
Blinkinlabs ICE40 programmer`. If the USB stick is also connected it
|
|
shows up as `1207:8887 Tillitis MTA1-USB-V1`.
|
|
|
|
To install the software needed for building and programming, please
|
|
refer to [toolchain_setup.md](toolchain_setup.md).
|
|
|
|
You are now ready to generate the FPGA bitstream (including building
|
|
the standard firmware) and program it onto the flash memory of the USB
|
|
stick. The following should be run as your regular non-root user, but
|
|
the programming is currently done using `sudo` (so sudo is expected to
|
|
be set up for your user; the Makefile runs `sudo tillitis-iceprog …`).
|
|
|
|
```
|
|
$ git clone https://github.com/tillitis/tillitis-key1
|
|
$ cd tillitis-key1/hw/application_fpga
|
|
$ make prog_flash
|
|
```
|
|
|
|
After programming, the Tillitis Key 1 USB stick can be connected to
|
|
your computer (use the USB-C-to-A adapter if needed) and will boot the
|
|
firmware. When boot has completed it will start flashing the LED
|
|
white. This indicates that it is ready to receive and measure an app.
|
|
|
|
To try out an app, continue to the README.md the apps repo:
|
|
https://github.com/tillitis/tillitis-key1-apps#readme
|
|
|
|
To learn more about the concepts and workings of the firmware, see:
|
|
[system_description/system_description.md](system_description/system_description.md)
|
|
and [system_description/software.md](system_description/software.md).
|
|
|
|
# Device personalization
|
|
|
|
To personalize Tillitis Key 1, you need to modify the hex file that
|
|
contains the Unique Device Secret (UDS). You should also update the
|
|
Unique Device Identity (UDI). These hex files are located in
|
|
`hw/application_fpga/data/`. Note that after modify the files in this
|
|
directory, you need to rebuild and program the device again (as
|
|
above).
|
|
|
|
To make this easier there is a tool that can generate these files. The
|
|
tool can be found in `hw/application_fpga/tools/tpt`. The tool allow
|
|
you to supply a secret used as part of the UDS generation. The tool
|
|
can be run interactively, or by suppling inputs on the command line:
|
|
|
|
```
|
|
usage: tpt.py [-h] [-v] [--ent ENT] [--vid VID] [--pid PID] [--rev REV] [--serial SERIAL]
|
|
|
|
options:
|
|
-h, --help show this help message and exit
|
|
-v, --verbose Verbose operation
|
|
--ent ENT User supplied entropy
|
|
--vid VID Vendor id (0 - 65535)
|
|
--pid PID Product id (0 - 2555
|
|
--rev REV Revision number (0 - 15)
|
|
--serial SERIAL Serial number (0 - (2**31 - 1))
|
|
```
|