mirror of
https://github.com/Qubes-Community/Contents.git
synced 2024-12-23 14:19:24 -05:00
74 lines
3.5 KiB
Markdown
74 lines
3.5 KiB
Markdown
---
|
|
layout: doc
|
|
title: Anonymizing your MAC Address
|
|
permalink: /doc/anonymizing-your-mac-address/
|
|
redirect_from:
|
|
- /doc/randomizing-your-mac-address/
|
|
---
|
|
|
|
Anonymizing your MAC Address
|
|
============================
|
|
|
|
Although it is not the only metadata broadcast by network hardware, changing the default [MAC Address](https://en.wikipedia.org/wiki/MAC_address) of your hardware could be [an important step in protecting privacy](https://tails.boum.org/contribute/design/MAC_address/#index1h1).
|
|
Currently, Qubes OS *does not* automatically "anonymize" or spoof the MAC Address, so unless this gets implemented by default you can randomize your MAC Address with the following guide.
|
|
|
|
|
|
## Upgrading and configuring Network Manager in Qubes
|
|
|
|
Newer versions of Network Manager have options for randomizing MAC addresses, and can handle the entire process across reboots, sleep/wake cycles and different connection states.
|
|
In particular, versions 1.4.2 and later should be well suited for Qubes. Qubes R4.0's default sys-net should have 1.8.2-4 by default.
|
|
However, use of the NetworkManager GUI to set these options is **unreliable** - there are numerous reports of changes not being saved for particular cards or interfaces.
|
|
You should check carefully that any settings you make in the GUI are saved, before relying on this method.
|
|
If the settings are not saved, you can use the method described below using a config file.
|
|
|
|
|
|
Network Manager 1.4.2 or later is available from the Fedora 25 repository as well as the Debian 10 repository.
|
|
|
|
Check that Network Manager version is now at least 1.4.2:
|
|
|
|
~~~
|
|
$ sudo NetworkManager -V
|
|
1.4.2
|
|
~~~
|
|
|
|
## Randomize a single connection
|
|
|
|
Right click on the Network Manager icon of your NetVM in the tray and click 'Edit Connections..'.
|
|
|
|
Select the connection to randomize and click Edit.
|
|
|
|
Select the Cloned MAC Address drop down and set to Random or Stable.
|
|
Stable will generate a random address that persists until reboot, while Random will generate an address each time a link goes up.
|
|
|
|
|
|
Save the change and reconnect the connection (click on Network Manager tray icon and click disconnect under the connection, it should automatically reconnect).
|
|
|
|
## Randomize all Ethernet and Wifi connections
|
|
|
|
These steps should be done inside a template to be used to create a NetVM as it relies on creating a config file that would otherwise be deleted after a reboot due to the nature of AppVMs.
|
|
|
|
Write the settings to a new file in the `/etc/NetworkManager/conf.d/` directory, such as `00-macrandomize.conf`.
|
|
The following example enables Wifi and Ethernet MAC address randomization while scanning (not connected), and uses a randomly generated but persistent MAC address for each individual Wifi and Ethernet connection profile.
|
|
|
|
~~~
|
|
[device]
|
|
wifi.scan-rand-mac-address=yes
|
|
|
|
[connection]
|
|
wifi.cloned-mac-address=stable
|
|
ethernet.cloned-mac-address=stable
|
|
connection.stable-id=${CONNECTION}/${BOOT}
|
|
~~~
|
|
|
|
* `stable` in combination with `${CONNECTION}/${BOOT}` generates a random address that persists until reboot.
|
|
* `random` generates a random address each time a link goes up.
|
|
|
|
To see all the available configuration options, refer to the man page: `man nm-settings`
|
|
|
|
Next, create a new NetVM using the edited template and assign network devices to it.
|
|
|
|
Finally, shutdown all VMs and change the settings of sys-firewall, etc. to use the new NetVM.
|
|
|
|
You can check the MAC address currently in use by looking at the status pages of your router device(s), or inside the NetVM with the command `sudo ip link show`.
|
|
|