mirror of
https://github.com/Qubes-Community/Contents.git
synced 2024-09-06 17:12:18 +00:00
93 lines
4.2 KiB
Markdown
93 lines
4.2 KiB
Markdown
Understanding and fixing issues with time/clock in Qubes OS
|
|
===========================================================
|
|
|
|
*Note: the content here is for Qubes 4.0, some things may be different in Qubes 3.2.*
|
|
|
|
Architecture
|
|
------------
|
|
|
|
### Timezone ###
|
|
|
|
The system's timezone is set in dom0.
|
|
|
|
VMs can read the system's timezone value from dom0 through the [QubesDB](https://www.qubes-os.org/doc/vm-interface/#qubesdb) `qubes-timezone` key. On Linux VMs with `qubes-core-agent` installed the time zone is set at boot time by the `/usr/lib/qubes/init/qubes-early-vm-config.sh` script.
|
|
|
|
|
|
### Clock synchronization ###
|
|
|
|
A VM is defined globally as "clockVM", from which other VMs and dom0 will synchronize their clock with. The following command in dom0 shows which VM is defined:
|
|
|
|
~~~
|
|
qubes-prefs clockvm
|
|
~~~
|
|
|
|
By default the clockvm is sys-net. Its clock is synchronized with remote NTP servers automatically by the `systemd-timesyncd` service.
|
|
|
|
The clockVM is the only VM to have a `/var/run/qubes-service/clocksync` file present. This file is used by various scripts and systemd service definitions to differentiate the clockVM from other VMs, which allows the clockVM to be based on the same template than other VMs.
|
|
|
|
Clock synchonization in other VMs is done:
|
|
|
|
- at boot time, by the `qubes-sync-time` service
|
|
- after suspend, by `/etc/qubes/suspend-post.d/qvm-sync-clock.sh`
|
|
- every 6 hours, by the `qubes-sync-time.timer` systemd timer
|
|
|
|
Those scripts run `/usr/bin/qvm-sync-clock` which uses the `qubes.GetDate` [RPC](https://www.qubes-os.org/doc/qrexec3/#qubes-rpc-services) call to obtain the date from the clockVM and run `/usr/lib/qubes/qubes-sync-clock` to validate the data received and set the date.
|
|
|
|
Clock synchonization in dom0 is done by the `/etc/cron.d/qubes-sync-clock.cron` cron job run every hour, which calls `/usr/bin/qvm-sync-clock` (despite scripts having the same filename in dom0 and VMs, they are different, but the end result is the same: `qubes.GetDate` RPC call, innput validation, and setting the date).
|
|
|
|
|
|
Debugging problems
|
|
------------------
|
|
|
|
### Time off by X hours ###
|
|
|
|
A common issue is to have the time off by a number of hours. There are usually two causes:
|
|
|
|
- Wrong configured timezone.
|
|
- MS Windows was used before installing Qubes OS (or in the case of dual-boot installations). Windows stores the time in the hardware clock as "local time" while Linux stores the time as UTC.
|
|
|
|
To check that the timezone is OK in dom0, run `timedatectl`. Alternatively, look at the `/etc/localtime` symlink: it should point to a timezone in `/usr/share/zoneinfo`. If you need to change the timezone in dom0, you can use
|
|
|
|
~~~
|
|
sudo timedatectl set-timezone "Australia/Queensland"
|
|
~~~
|
|
|
|
or
|
|
|
|
~~~
|
|
sudo rm /etc/localtime
|
|
sudo ln -s /usr/share/zoneinfo/Australia/Queensland /etc/localtime
|
|
~~~
|
|
|
|
To set the system's hardware clock to UTC, run the following command in the clockVM (usually sys-net):
|
|
|
|
~~~
|
|
sudo hwclock --systohc --utc
|
|
~~~
|
|
|
|
Then the easiest way to have the changes applied to all VMs is to do a full reboot.
|
|
|
|
|
|
### Wrong time/date ###
|
|
|
|
It is also possible that the clockVM's clock isn't properly synchronized with remote NTP servers. Check the status of the systemd-timesyncd service with `systemctl status systemd-timesyncd` in the clockVM (usuall sys-net):
|
|
|
|
~~~
|
|
● systemd-timesyncd.service - Network Time Synchronization
|
|
Loaded: loaded (/usr/lib/systemd/system/systemd-timesyncd.service; enabled; vendor preset: enabled)
|
|
Drop-In: /usr/lib/systemd/system/systemd-timesyncd.service.d
|
|
└─30_qubes.conf
|
|
Active: active (running) since Sun 2018-04-29 06:59:59 EEST; 1 weeks 1 days ago
|
|
Docs: man:systemd-timesyncd.service(8)
|
|
Main PID: 16966 (systemd-timesyn)
|
|
Status: "Synchronized to time server 95.87.227.232:123 (0.fedora.pool.ntp.org)."
|
|
Tasks: 2 (limit: 4915)
|
|
CGroup: /system.slice/systemd-timesyncd.service
|
|
└─16966 /usr/lib/systemd/systemd-timesyncd
|
|
~~~
|
|
|
|
In the output above, the clock was successfully synchronized with the `0.fedora.pool.ntp.org` server. The output might be empty if logs were rotated though, in that case restart the service with `systemctl restart systemd-timesyncd` and recheck its status.
|
|
|
|
No clock synchronization usually means the clockVM has a problem with networking.
|
|
|