mirror of
https://github.com/QubesOS/qubes-doc.git
synced 2024-10-01 01:25:40 -04:00
c091be36ca
I initially ignored this page because the described symptoms did not match the behavior I was experiencing, and wasted about a week trying to figure out what was wrong.
67 lines
3.0 KiB
Markdown
67 lines
3.0 KiB
Markdown
---
|
|
layout: doc
|
|
title: UEFI Troubleshooting
|
|
permalink: /doc/uefi-troubleshooting/
|
|
---
|
|
|
|
Troubleshooting UEFI related problems
|
|
========================================
|
|
|
|
|
|
Cannot start installation, installation completes successfully but then BIOS loops at boot device selection, hangs at four penguins after choosing "Test media and install Qubes OS" in GRUB menu
|
|
---------------------
|
|
|
|
There is some [common bug in UEFI implementation](http://xen.markmail.org/message/f6lx2ab4o2fch35r), affecting mostly Lenovo systems, but probably some others too. You can try existing workaround:
|
|
|
|
01. In GRUB menu<sup id="a1-1">[1](#f1)</sup>, select "Troubleshoot", then "Boot from device", then press `e`.
|
|
02. At the end of `chainloader` line add `/mapbs /noexitboot`.
|
|
03. Perform installation normally, but not reboot system at the end yet.
|
|
04. Go to `tty2` (Ctrl-Alt-F2).
|
|
05. Enable `/mapbs /noexitboot` on just installed system. This step differs between Qubes releases:
|
|
|
|
**For Qubes 3.1:**
|
|
|
|
06. Execute `mount | grep boot/efi` and note device name (first column). It should be something like `/dev/sda1`.
|
|
07. Execute `efibootmgr -v`, search for `Qubes` entry and note its number (it should be something like `Boot0001` - `0001` is an entry number).
|
|
08. Replace existing `Qubes` entry with modified one. Replace `XXXX` with entry number from previous step, `/dev/sda` with your disk name and `-p 1` with `/boot/efi` partition number):
|
|
|
|
efibootmgr -b XXXX -B
|
|
efibootmgr -v -c -u -L Qubes -l /EFI/qubes/xen.efi -d /dev/sda -p 1 "placeholder /mapbs /noexitboot"
|
|
|
|
09. Compare new entry with the old one (printed in step 6) - it should only differ in additional options at the end.
|
|
10. Now you can reboot the system by issuing `reboot` command.
|
|
|
|
**For Qubes 3.2 or later:**
|
|
|
|
11. Edit `/mnt/sysimage/boot/efi/EFI/qubes/xen.cfg` (you can use `vi` editor) and add to every kernel section:
|
|
|
|
mapbs=1
|
|
noexitboot=1
|
|
|
|
**Note:** You must add these parameters on two separate new lines (one
|
|
paramater on each line) at the end of each section that includes a kernel
|
|
line (i.e., all sections except the first one, since it doesn't have a
|
|
kernel line).
|
|
|
|
12. Now you can reboot the system by issuing `reboot` command.
|
|
|
|
|
|
System crash/restart when booting installer
|
|
-------------------------------------------
|
|
|
|
Some Dell systems and probably others have [another bug in UEFI firmware](http://markmail.org/message/amw5336otwhdxi76). And there is another workaround for it:
|
|
|
|
|
|
1. In GRUB menu<sup id="a1-2">[1](#f1)</sup> press `e`.
|
|
2. At the end of `chainloader` line add `-- efi=attr=uc`.
|
|
3. Perform installation normally, but not reboot system at the end yet.
|
|
4. Go to `tty2` (Ctrl-Alt-F2).
|
|
5. Execute:
|
|
|
|
sed -i -e 's/^options=.*/\0 efi=attr=uc' /mnt/sysimage/boot/efi/qubes/xen.cfg
|
|
|
|
6. Now you can reboot the system by issuing `reboot` command.
|
|
|
|
* * *
|
|
<b name="f1">1</b> If you use rEFInd, you can see 3 options regarding the USB installer. Choose "Fallback Boot Loader" to enter the GRUB menu. [↩](#a1-1) [↩](#a1-2)
|