portapack-mayhem/firmware/chibios/boards/EA_LPCXPRESSO_LPC812/board.h

126 lines
4.1 KiB
C
Executable File

/*
ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software
distributed under the License is distributed on an "AS IS" BASIS,
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and
limitations under the License.
*/
#ifndef _BOARD_H_
#define _BOARD_H_
/*
* Setup for Embedded Artists LPCXpresso LPC812 board.
*/
/*
* Board identifiers.
*/
#define BOARD_EA_LPC812
#define BOARD_NAME "Embedded Artists LPCXpresso LPC812"
/*
* Board frequencies.
*/
#define SYSOSCCLK 12000000
/*
* I/O ports initial setup, this configuration is established soon after reset
* in the initialization code.
* Please refer to the LPC8xx Reference Manual for details.
*/
/* Pull-up/down */
#define PIN_MODE_NOPULL (0<<3)
#define PIN_MODE_PULLDOWN (1<<3)
#define PIN_MODE_PULLUP (2<<3)
#define PIN_MODE_REPEATER (3<<3)
/* Hysteresis */
#define PIN_HYS_EN (1<<5)
/* Invert Input */
#define PIN_INV_INPUT (1<<6)
/* Reserved bits */
#define PIN_RSVD (1<<7)
/* I2C Mode */
#define PIN_I2CMODE_STD (0<<8)
#define PIN_I2CMODE_STDIO (1<<8)
#define PIN_I2CMODE_FAST (2<<8)
/* Open Drain */
#define PIN_OPEN_DRAIN (1<<10)
/* Input Filter Sample Clocks */
#define PIN_SMODE_FILTER(n) ((n)<<11)
/* Input Filter clock divider */
#define PIN_CLKDIV_FILTER(n) ((n)<<13)
/*
* Pin definitions.
*/
#define LED_RED 7
#define LED_BLUE 16
#define LED_GREEN 17
/*
* GPIO 0 initial setup.
*/
/*#define VAL_PIO0_0 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_1 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_2 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_3 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_4 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_5 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_6 PIN_MODE_PULLUP*/
#define VAL_PIO0_7 PIN_MODE_NOPULL
/*#define VAL_PIO0_8 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_9 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_10 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_11 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_12 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_13 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_14 PIN_MODE_PULLUP*/
/*#define VAL_PIO0_15 PIN_MODE_PULLUP*/
#define VAL_PIO0_16 PIN_MODE_NOPULL
#define VAL_PIO0_17 PIN_MODE_NOPULL
/* UART0: TXD = P0.4, RXD = P0.0)*/
#define VAL_PINASSIGN0 ((0xFFFF0000) | (0<<8) | (4))
/*#define VAL_PINASSIGN1 0xFFFFFFFF*/
/*#define VAL_PINASSIGN2 0xFFFFFFFF*/
/*#define VAL_PINASSIGN3 0xFFFFFFFF*/
/*#define VAL_PINASSIGN4 0xFFFFFFFF*/
/*#define VAL_PINASSIGN5 0xFFFFFFFF*/
/*#define VAL_PINASSIGN6 0xFFFFFFFF*/
/*#define VAL_PINASSIGN7 0xFFFFFFFF*/
/*#define VAL_PINASSIGN8 0xFFFFFFFF*/
#define VAL_GPIO0DIR (PAL_PORT_BIT(LED_RED) | \
PAL_PORT_BIT(LED_BLUE) | \
PAL_PORT_BIT(LED_GREEN))
#define VAL_GPIO0DATA (PAL_PORT_BIT(LED_RED) | \
PAL_PORT_BIT(LED_BLUE) | \
PAL_PORT_BIT(LED_GREEN))
#if !defined(_FROM_ASM_)
#ifdef __cplusplus
extern "C" {
#endif
void boardInit(void);
#ifdef __cplusplus
}
#endif
#endif /* _FROM_ASM_ */
#endif /* _BOARD_H_ */