mirror of
https://github.com/eried/portapack-mayhem.git
synced 2024-12-12 09:14:30 -05:00
d4c43044e0
Bootstrap is now 64k @ 0x00000. HackRF image is 64k @ 0x10000. Baseband image is 128k @ 0x20000. Application image is remainder of SPI flash, @ 0x40000.
114 lines
3.5 KiB
C
114 lines
3.5 KiB
C
/*
|
|
* Copyright (C) 2015 Jared Boone, ShareBrained Technology, Inc.
|
|
*
|
|
* This file is part of PortaPack.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2, or (at your option)
|
|
* any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; see the file COPYING. If not, write to
|
|
* the Free Software Foundation, Inc., 51 Franklin Street,
|
|
* Boston, MA 02110-1301, USA.
|
|
*/
|
|
|
|
#include <lpc43xx_m4.h>
|
|
#include <nvic.h>
|
|
|
|
/* Bootstrap runs from SPIFI on the M4, immediately after the LPC43xx built-in
|
|
* boot ROM runs.
|
|
*/
|
|
|
|
/* After boot ROM executes:
|
|
* PLL1 is at 288MHz (IRC * 24)
|
|
* IDIVB_CTRL = PLL1 / 9 = 32MHz
|
|
* IDIVC_CTRL = PLL1 / 3 = 96MHz
|
|
* BASE_SPIFI_CLK.CLK_SEL = IDIVB
|
|
*/
|
|
|
|
/* SPIFI config must run from RAM because SPIFI memory mode may/must be
|
|
* re-initialized during the transition
|
|
*/
|
|
/* An ARM veneer will be created to make the long jump between code in the
|
|
* SPIFI address range and the RAM address range.
|
|
*/
|
|
__attribute__ ((section("fast")))
|
|
void configure_spifi(void) {
|
|
/* Configure pins first, to enable SCK input buffer for feedback */
|
|
|
|
/* Configure SPIFI pins for maximum I/O rate */
|
|
const uint32_t scu_spifi_io =
|
|
(3 << 0) /* Function 3 */
|
|
| (0 << 3) /* Disable pull-down */
|
|
| (1 << 4) /* Disable pull-up */
|
|
| (1 << 5) /* Fast slew rate */
|
|
| (1 << 6) /* Enable input buffer */
|
|
| (1 << 7) /* Disable input glitch filter */
|
|
;
|
|
LPC_SCU->SFSP3_3 = scu_spifi_io;
|
|
LPC_SCU->SFSP3_4 = scu_spifi_io;
|
|
LPC_SCU->SFSP3_5 = scu_spifi_io;
|
|
LPC_SCU->SFSP3_6 = scu_spifi_io;
|
|
LPC_SCU->SFSP3_7 = scu_spifi_io;
|
|
LPC_SCU->SFSP3_8 = scu_spifi_io;
|
|
|
|
/* Tweak SPIFI mode */
|
|
LPC_SPIFI->CTRL =
|
|
(0xffff << 0) /* Timeout */
|
|
| (0x1 << 16) /* CS high time in "clocks - 1" */
|
|
| (0 << 21) /* 0: Attempt speculative prefetch on data accesses */
|
|
| (0 << 22) /* 0: No interrupt on command ended */
|
|
| (0 << 23) /* 0: SCK driven low after rising edge at which last bit of command is captured. Stays low while CS# is high. */
|
|
| (0 << 27) /* 0: Cache prefetching enabled */
|
|
| (0 << 28) /* 0: Quad protocol, IO3:0 */
|
|
| (1 << 29) /* 1: Read data sampled on falling edge of clock */
|
|
| (1 << 30) /* 1: Read data is sampled using feedback clock from SCK pin */
|
|
| (0 << 31) /* 0: DMA request disabled */
|
|
;
|
|
|
|
/* Throttle up the SPIFI interface to 96MHz (PLL1 / 3) */
|
|
LPC_CGU->IDIVB_CTRL =
|
|
(0 << 0) /* PD */
|
|
| (1 << 2) /* IDIV (/2) */
|
|
| (1 << 11) /* AUTOBLOCK */
|
|
| (9 << 24) /* PLL1 */
|
|
;
|
|
}
|
|
|
|
int main(void) {
|
|
#if 0
|
|
/* Configure LEDs and make sure they're off to start */
|
|
LPC_SCU->SFSP4_1 = (1 << 4) | 0; /* GPIO2[1] */
|
|
LPC_SCU->SFSP4_2 = (1 << 4) | 0; /* GPIO2[2] */
|
|
LPC_SCU->SFSP6_12 = (1 << 4) | 0; /* GPIO2[8] */
|
|
LPC_GPIO->CLR[2] = (1 << 8) | (1 << 2) | (1 << 1);
|
|
LPC_GPIO->DIR[2] = (1 << 8) | (1 << 2) | (1 << 1);
|
|
|
|
/* Indicate M4 is working */
|
|
LPC_GPIO->SET[2] = (1 << 1);
|
|
#endif
|
|
configure_spifi();
|
|
|
|
/* NOTE: MEMMAP registers are ORed with the shadow address to create the
|
|
* actual address.
|
|
*/
|
|
LPC_CREG->M0APPMEMMAP = LPC_SPIFI_DATA_CACHED_BASE + 0x40000;
|
|
|
|
/* Change M0APP_RST to 0 */
|
|
LPC_RGU->RESET_CTRL[1] = 0;
|
|
|
|
while(1) {
|
|
__WFE();
|
|
}
|
|
}
|
|
|
|
void SystemInit(void) {
|
|
}
|