diff --git a/firmware/application/apps/ui_mictx.cpp b/firmware/application/apps/ui_mictx.cpp index 0e2c9c47..bda0f278 100644 --- a/firmware/application/apps/ui_mictx.cpp +++ b/firmware/application/apps/ui_mictx.cpp @@ -24,6 +24,10 @@ #include "baseband_api.hpp" #include "audio.hpp" + +#include "wm8731.hpp" +using wolfson::wm8731::WM8731; + #include "tonesets.hpp" #include "portapack_hal.hpp" #include "string_format.hpp" @@ -34,6 +38,10 @@ using namespace tonekey; using namespace portapack; + +WM8731 audio_codec_wm8731 { i2c0, 0x1a }; + + namespace ui { void MicTXView::focus() { @@ -178,7 +186,7 @@ void MicTXView::rxaudio(bool is_on) { baseband::run_image(portapack::spi_flash::image_tag_mic_tx); audio::output::stop(); - audio::input::start(); + audio::input::start(ak4951_alc_GUI_selected); // set up audio input = mic config of any audio coded AK4951/WM8731, (in WM8731 parameter will be ignored) portapack::pin_i2s0_rx_sda.mode(3); configure_baseband(); } @@ -203,10 +211,12 @@ MicTXView::MicTXView( baseband::run_image(portapack::spi_flash::image_tag_mic_tx); - add_children({ - &labels, + + if ( audio_codec_wm8731.detected() ) { + add_children({ + &labels_WM8731, // we have audio codec WM8731, same MIC menu as original. &vumeter, - &options_gain, + &options_gain, // MIC GAIN float factor on the GUI. // &check_va, &field_va, &field_va_level, @@ -229,6 +239,37 @@ MicTXView::MicTXView( &field_rxamp, &tx_button }); + + } else { + add_children({ + &labels_AK4951, // we have audio codec AK4951, enable Automatic Level Control + &vumeter, + &options_gain, + &options_ak4951_alc_mode, +// &check_va, + &field_va, + &field_va_level, + &field_va_attack, + &field_va_decay, + &field_bw, + &field_rfgain, + &field_rfamp, + &options_mode, + &field_frequency, + &options_tone_key, + &check_rogerbeep, + &check_rxactive, + &field_volume, + &field_rxbw, + &field_squelch, + &field_rxfrequency, + &field_rxlna, + &field_rxvga, + &field_rxamp, + &tx_button + }); + + } tone_keys_populate(options_tone_key); options_tone_key.on_change = [this](size_t i, int32_t) { @@ -242,6 +283,12 @@ MicTXView::MicTXView( }; options_gain.set_selected_index(1); // x1.0 + options_ak4951_alc_mode.on_change = [this](size_t, int8_t v) { + ak4951_alc_GUI_selected = v; + audio::input::start(ak4951_alc_GUI_selected); + }; + // options_ak4951_alc_mode.set_selected_index(0); + tx_frequency = transmitter_model.tuning_frequency(); field_frequency.set_value(transmitter_model.tuning_frequency()); field_frequency.set_step(receiver_model.frequency_step()); @@ -478,7 +525,7 @@ MicTXView::MicTXView( set_tx(false); audio::set_rate(audio::Rate::Hz_24000); - audio::input::start(); + audio::input::start(ak4951_alc_GUI_selected); // originally , audio::input::start(); (we added parameter) } MicTXView::~MicTXView() { diff --git a/firmware/application/apps/ui_mictx.hpp b/firmware/application/apps/ui_mictx.hpp index 9084047a..aaab059c 100644 --- a/firmware/application/apps/ui_mictx.hpp +++ b/firmware/application/apps/ui_mictx.hpp @@ -83,6 +83,7 @@ private: bool rx_enabled { false }; uint32_t tone_key_index { }; float mic_gain { 1.0 }; + uint8_t ak4951_alc_GUI_selected { 0 }; uint32_t audio_level { 0 }; uint32_t va_level { }; uint32_t attack_ms { }; @@ -106,8 +107,8 @@ private: bool enable_lsb { false }; - Labels labels { - { { 3 * 8, 1 * 8 }, "MIC. GAIN:", Color::light_grey() }, + Labels labels_WM8731 { + { { 3 * 8, 1 * 8 }, "MIC-GAIN:", Color::light_grey() }, { { 3 * 8, 3 * 8 }, "F:", Color::light_grey() }, { { 15 * 8, 3 * 8 }, "BW: FM kHz", Color::light_grey() }, { { 3 * 8, 5 * 8 }, "GAIN:", Color::light_grey() }, @@ -118,15 +119,36 @@ private: { {12 * 8, 10 * 8 }, "ATT:", Color::light_grey() }, { {20 * 8, 10 * 8 }, "DEC:", Color::light_grey() }, { { 4 * 8, ( 13 * 8 ) - 2 }, "TONE KEY:", Color::light_grey() }, - { { 9 * 8, 23 * 8 }, "VOL:", Color::light_grey() }, - { {17 * 8, 23 * 8 }, "FM RXBW:", Color::light_grey() }, + { { 7 * 8, 23 * 8 }, "VOL:", Color::light_grey() }, + { {15 * 8, 23 * 8 }, "FM RXBW:", Color::light_grey() }, { {17 * 8, 25 * 8 }, "SQ:", Color::light_grey() }, { { 5 * 8, 25 * 8 }, "F:", Color::light_grey() }, { { 5 * 8, 27 * 8 }, "LNA:", Color::light_grey()}, { {12 * 8, 27 * 8 }, "VGA:", Color::light_grey()}, { {19 * 8, 27 * 8 }, "AMP:", Color::light_grey()} }; - + Labels labels_AK4951 { + { { 3 * 8, 1 * 8 }, "MIC-GAIN:", Color::light_grey() }, + { { 17 * 8, 1 * 8 }, "ALC", Color::light_grey() }, + { { 3 * 8, 3 * 8 }, "F:", Color::light_grey() }, + { { 15 * 8, 3 * 8 }, "BW: FM kHz", Color::light_grey() }, + { { 3 * 8, 5 * 8 }, "GAIN:", Color::light_grey() }, + { {11 * 8, 5 * 8 }, "Amp:", Color::light_grey() }, + { { 18 * 8, (5 * 8) }, "Mode:", Color::light_grey() }, + { { 3 * 8, 8 * 8 }, "TX Activation:", Color::light_grey() }, + { { 4 * 8, 10 * 8 }, "LVL:", Color::light_grey() }, + { {12 * 8, 10 * 8 }, "ATT:", Color::light_grey() }, + { {20 * 8, 10 * 8 }, "DEC:", Color::light_grey() }, + { { 4 * 8, ( 13 * 8 ) - 2 }, "TONE KEY:", Color::light_grey() }, + { { 7 * 8, 23 * 8 }, "VOL:", Color::light_grey() }, + { {15 * 8, 23 * 8 }, "FM RXBW:", Color::light_grey() }, + { {17 * 8, 25 * 8 }, "SQ:", Color::light_grey() }, + { { 5 * 8, 25 * 8 }, "F:", Color::light_grey() }, + { { 5 * 8, 27 * 8 }, "LNA:", Color::light_grey()}, + { {12 * 8, 27 * 8 }, "VGA:", Color::light_grey()}, + { {19 * 8, 27 * 8 }, "AMP:", Color::light_grey()} + }; + VuMeter vumeter { { 0 * 8, 1 * 8, 2 * 8, 33 * 8 }, 12, @@ -135,7 +157,7 @@ private: OptionsField options_gain { - { 13 * 8, 1 * 8 }, + { 12 * 8, 1 * 8 }, 4, { { "x0.5", 5 }, @@ -145,6 +167,25 @@ private: } }; + OptionsField options_ak4951_alc_mode { + { 20 * 8, 1 * 8 }, // Coordinates are: int:x (px), int:y (px) + 11, + { + { " OFF-20kHz", 0 }, // Nothing changed from ORIGINAL,keeping ALL programm. AK4951 Dig. block->OFF) + { "+12dB-6kHz", 1 }, // ALC-> on, (+12dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "+09dB-6kHz", 2 }, // ALC-> on, (+09dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "+06dB-6kHz", 3 }, // ALC-> on, (+06dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "+03dB-2kHz", 4 }, // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + LPF 3,5k + Pre-amp Mic (+21dB=original)+ EQ boosting ~<2kHz (f0~1k1,fb:1,7K, k=1,8) + { "+03dB-4kHz", 5 }, // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + LPF 4kHz + Pre-amp Mic (+21dB=original)+ EQ boosting ~<3kHz (f0~1k4,fb~2,4k, k=1,8) + { "+03dB-6kHz", 6 }, // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "+00dB-6kHz", 7 }, // ALC-> on, (+00dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "-03dB-6kHz", 8 }, // ALC-> on, (-03dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "-06dB-6kHz", 9 }, // ALC-> on, (-06dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + { "-09dB-6kHz", 10 }, // ALC-> on, (-09dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz - Pre-amp MIC -3dB (18dB's) + { "-12dB-6kHz", 11 }, // ALC-> on, (-12dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz - Pre-amp MIC -6dB (15dB's) + } + }; + FrequencyField field_frequency { { 5 * 8, 3 * 8 }, }; @@ -244,7 +285,7 @@ private: }; NumberField field_volume { - { 13 * 8, 23 * 8 }, + { 11* 8, 23 * 8 }, 2, { 0, 99 }, 1, @@ -252,7 +293,7 @@ private: }; OptionsField field_rxbw { - { 25 * 8, 23 * 8}, + { 23* 8, 23 * 8}, 3, { {"8k5", 0}, diff --git a/firmware/application/audio.cpp b/firmware/application/audio.cpp index 4ba23acc..ce32076c 100644 --- a/firmware/application/audio.cpp +++ b/firmware/application/audio.cpp @@ -168,8 +168,8 @@ void speaker_mute() { namespace input { -void start() { - audio_codec->microphone_enable(); +void start(int8_t alc_mode) { + audio_codec->microphone_enable(alc_mode); // added user-GUI selection for AK4951, ALC mode parameter. i2s::i2s0::rx_start(); } diff --git a/firmware/application/audio.hpp b/firmware/application/audio.hpp index b02e42aa..56301ee8 100644 --- a/firmware/application/audio.hpp +++ b/firmware/application/audio.hpp @@ -49,7 +49,7 @@ public: virtual volume_range_t headphone_gain_range() const = 0; virtual void set_headphone_volume(const volume_t volume) = 0; - virtual void microphone_enable() = 0; + virtual void microphone_enable(int8_t alc_mode) = 0; // added user-GUI AK4951 ,selected ALC mode. virtual void microphone_disable() = 0; virtual size_t reg_count() const = 0; @@ -59,7 +59,7 @@ public: namespace output { -void start(); +void start(); // this other start(),no changed. ,in namespace output , used to config audio playback mode, void stop(); void mute(); @@ -72,7 +72,7 @@ void speaker_unmute(); namespace input { -void start(); +void start(int8_t alc_mode); // added parameter user-GUI select AK4951-ALC mode for config mic path,(recording mode in datasheet), void stop(); } /* namespace input */ diff --git a/firmware/common/ak4951.cpp b/firmware/common/ak4951.cpp index 3556e0a5..d94bbb0b 100644 --- a/firmware/common/ak4951.cpp +++ b/firmware/common/ak4951.cpp @@ -212,90 +212,347 @@ void AK4951::speaker_disable() { set_speaker_power(false); } -void AK4951::microphone_enable() { -// map.r.digital_mic.DMIC = 0; -// update(Register::DigitalMic); +void AK4951::microphone_enable(int8_t alc_mode) { +// alc_mode =0 = (OFF =same as original code = NOT using AK4951 Programmable digital filter block), +// alc_mode >1 (with DIGITAL FILTER BLOCK , example : 1:(+12dB) , 2:(+9dB)", 3:(+6dB), ...) + +// map.r.digital_mic.DMIC = 0; // originally commented code +// update(Register::DigitalMic); // originally commented code + +uint_fast8_t mgain =0b0111; // Pre-amp mic (Original code, =0b0111 (+21dB's=7x3dBs),(Max is NOT 0b1111!, it is 0b1010=+30dBs=10x3dBs) + +map.r.signal_select_2.INL = 0b01; // Lch input signal = LIN2 , our ext. MONO MIC is connected here LIN2 in Portapack. +map.r.signal_select_2.INR = 0b01; // Rch input signal = RIN2 , Not used ,not connected ,but no problem. +map.r.signal_select_2.MICL = 0; // MPWR = 2.4V (it has two possible settings , 2.4V or 2.0V) , (majority smarthphones around 2V , range 1V-5V) +update(Register::SignalSelect2); + +// ------Common code part, = original setting conditions, it is fine for all user-GUI alc_modes: OFF , and ALC modes .*/ +map.r.digital_filter_select_1.HPFAD = 1; // HPF1 ON (after ADC);page 40 datasheet, HPFAD bit controls the ON/OFF of the HPF1 (HPF ON is recommended). +map.r.digital_filter_select_1.HPFC = 0b11; // HPF Cut off frequency of high pass filter from 236.8 Hz @fs=48k ("00":3.7Hz, "01":14,8Hz, "10":118,4Hz) +update(Register::DigitalFilterSelect1); + +// map.r.r_ch_mic_gain_setting.MGR = 0x80; // Microphone sensitivity correction = 0dB., (not used by now , original code cond.) +// update(Register::RchMicGainSetting); // (those two lines , not activated, same as original) + +// pre-load 4 byes LPF coefficicients (.lpf_coefficient_0,1,2,3), FSA 14..0, FSB 14..0 , (fcut initial 6kHz, fs 48Khz). +// it will be default pre-loading coeff. for al ALC modes, LPF bit is activated down, for all ALC digital modes. +map.r.lpf_coefficient_0.l = 0x5F; // Pre-loading here LPF 6kHz, 1st Order from digital Block , Fc=6000 Hz, fs = 48khz +map.r.lpf_coefficient_1.h = 0x09; // LPF bit is activated down, for all ALC digital modes. +map.r.lpf_coefficient_2.l = 0xBF; // Writting reg to AK4951, with "update", following instructions. +map.r.lpf_coefficient_3.h = 0x32; + +update(Register::LPFCoefficient0); // Writing pre-loaded 4 bytes LPF CoefFiecients 14 bits (FSA13..0, FSB13..0 +update(Register::LPFCoefficient1); // In this case , LPF 6KHz , when we activate the LPF block. +update(Register::LPFCoefficient2); +update(Register::LPFCoefficient3); + +// Reset , setting OFF all 5 x Digital Equalizer filters +map.r.digital_filter_select_3.EQ1 = 0; // EQ1 Coeffic Setting , (0: Disable-default, audio data passes EQ1 block by 0dB gain). When EQ1="1”, the settings of E1A15-0, E1B15-0 and E1C15-0 bits are enabled +map.r.digital_filter_select_3.EQ2 = 0; // EQ2 Coeffic Setting , (0: Disable-default, audio data passes EQ2 block by 0dB gain). When EQ2="1”, the settings of E2A15-0, E2B15-0 and E2C15-0 bits are enabled +map.r.digital_filter_select_3.EQ3 = 0; // EQ3 Coeffic Setting , (0: Disable-default, audio data passes EQ3 block by 0dB gain). When EQ3="1”, the settings of E3A15-0, E3B15-0 and E3C15-0 bits are enabled +map.r.digital_filter_select_3.EQ4 = 0; // EQ4 Coeffic Setting , (0: Disable-default, audio data passes EQ4 block by 0dB gain). When EQ4="1”, the settings of E4A15-0, E4B15-0 and E4C15-0 bits are enabled +map.r.digital_filter_select_3.EQ5 = 0; // EQ5 Coeffic Setting , (0: Disable-default, audio data passes EQ5 block by 0dB gain). When EQ5="1”, the settings of E5A15-0, E5B15-0 and E5C15-0 bits are enabled +update(Register::DigitalFilterSelect3); // A,B,C EQ1 Coefficients are already pre-loaded in ak4951.hpp + + + if (alc_mode==0) { // Programmable Digital Filter OFF, same as original condition., no Digital ALC, nor Wind Noise Filter, LPF , EQ + + map.r.digital_filter_select_2.LPF = 0; // LPF-Block, Coeffic Setting Enable (OFF-Default), When LPF bit is “0”, audio data passes the LPF block by 0dB gain. + update(Register::DigitalFilterSelect2); + + // Pre-loading AUDIO PATH with all DIGITAL BLOCK by pased, see, audio path block diagramm AK4951 datasheet + Table Playback mode -Recording mode. + // Digital filter block PATH is BY PASSED (we can swith off DIG. BLOCK power , PMPFIL=0) .The Path in Recording Mode 2 & Playback Mode 2 (NO DIG FILTER BLOCK AT ALL, not for MIC recording, nor for Playback) + map.r.digital_filter_mode.ADCPF = 1; // ADCPF bit swith ("0" Mic after ADC Output connected (recording mode) to the DIGITAL FILTER BLOCK. ("1" Playback mode) + map.r.digital_filter_mode.PFSDO = 0; // ADC bit switch ("0" : 1st order HPF) connectedto the Output. By bass DIGITAL block . + map.r.digital_filter_mode.PFDAC = 0b00; // (Input selector for DAC (not used in MIC), SDTI= Audio Serial Data Input Pin) + update(Register::DigitalFilterMode); // Writing the Audio Path : NO DIGITAL BLOCK or DIG BLOCK FOR MIC , Audio mode path : Playback mode /-Recording mode. + + map.r.power_management_1.PMADL = 1; // ADC Lch = Lch input signal. Mic Amp Lch and ADC Lch Power Management + map.r.power_management_1.PMADR = 1; // ADC Rch = Rch input signal. Mic Amp Rch and ADC Rch Power Management + map.r.power_management_1.PMPFIL = 0; // Pre-loading , Programmable Dig. filter OFF ,filter unused, routed around.(original value = 0 ) + update(Register::PowerManagement1); // Activating the Power management of the used blocks . (Mic ADC always + Dig Block filter , when used ) + + // 1059/fs, 22ms @ 48kHz + chThdSleepMilliseconds(22); + + } else { // ( alc_mode !=0) + + switch(alc_mode) { // Pre-loading register values depending on user-GUI selection (they will be sended below, with "update(Register_name::xxx )". + + case 1: // ALC-> on, (+12dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0xC0; // REF7-0 bits,max gain at ALC recovery operation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, C0H=+12dBs) + map.r.l_ch_input_volume_control.IV = 0xC0; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xC0; // Right Input Dig Vol Setting, same comment as above , The value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 2: // ALC-> on, (+09dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0xB8; // REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, B8H= +9dBs) + map.r.l_ch_input_volume_control.IV = 0xB8; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xB8; // Right Input Dig Vol Setting, same comment as above , The value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 3: // ALC-> on, (+06dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0xB0; // 0xB8 , REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, B0H= +6dBs) + map.r.l_ch_input_volume_control.IV = 0xB0; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xB0; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 4: // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + Pre-amp Mic (+21dB=original) + // + EQ boosting ~<2kHz (f0:1,1k, fb:1,7K, k=1,8) && + LPF 3,5k + map.r.alc_mode_control_2.REF = 0xA8; // 0xA8 , REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, A8H= +3dBs) + map.r.l_ch_input_volume_control.IV = 0xA8; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xA8; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + //The EQn (n=1, 2, 3, 4 or 5) coefficient must be set when EQn bit = “0” or PMPFIL bit = “0”. + map.r.digital_filter_select_3.EQ1 = 1; // EQ1 Coeffic Setting , (0: Disable-default, audio data passes EQ1 block by 0dB gain). When EQ1="1”, the settings of E1A15-0, E1B15-0 and E1C15-0 bits are enabled + update(Register::DigitalFilterSelect3); // A,B,C EQ1 Coefficients are already pre-loaded in ak4951.hpp + + map.r.lpf_coefficient_0.l = 0x0D; // Pre-loading here LPF 3,5k , 1st Order from digital Block , Fc=3.500 Hz, fs = 48khz + map.r.lpf_coefficient_1.h = 0x06; // LPF bit is activated down, for all ALC digital modes. + map.r.lpf_coefficient_2.l = 0x1A; // Writting reg to AK4951 , down with update.... + map.r.lpf_coefficient_3.h = 0x2C; + // LPF bit is activated down, for all ALC digital modes. + break; + + case 5: // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + Pre-amp Mic (+21dB=original) + // + EQ boosting ~<3kHz (f0~1k4,fb~2,4k,k=1,8) && LPF 4kHz + map.r.alc_mode_control_2.REF = 0xA8; // 0xA0 , REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, A8H= +3dBs) + map.r.l_ch_input_volume_control.IV = 0xA8; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xA8; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + map.r.digital_filter_select_3.EQ2 = 1; // EQ2 Coeffic Setting , (0: Disable-default, audio data passes EQ2 block by 0dB gain). When EQ2="1”, the settings of E2A15-0, E2B15-0 and E2C15-0 bits are enabled + update(Register::DigitalFilterSelect3); + + map.r.lpf_coefficient_0.l = 0xC3; // Pre-loading here LPF 4k , 1st Order from digital Block , Fc=4000 Hz, fs = 48khz + map.r.lpf_coefficient_1.h = 0x06; // LPF bit is activated down, for all ALC digital modes. + map.r.lpf_coefficient_2.l = 0x86; // Writting reg to AK4951 , down with update.... + map.r.lpf_coefficient_3.h = 0x2D; + // LPF bit is activated down, for all ALC digital modes. + break; + + case 6: // ALC-> on, (+03dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0xA8; // REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, A0H= 0dBs) + map.r.l_ch_input_volume_control.IV = 0xA8; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xA8; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 7: // ALC-> on, (+00dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0xA0; // REF7-0 bits,max gain at ALC recoveryoperation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, A0H= 0dBs) + map.r.l_ch_input_volume_control.IV = 0xA0; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0xA0; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 8: // ALC-> on, (-03dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0x98; //REF7-0 bits,max gain at ALC recovery operation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, 98H=-03dBs) + map.r.l_ch_input_volume_control.IV = 0x98; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0x98; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s - const uint_fast8_t mgain = 0b0111; - map.r.signal_select_1.MGAIN20 = mgain & 7; - map.r.signal_select_1.PMMP = 1; - map.r.signal_select_1.MPSEL = 1; // MPWR2 pin - map.r.signal_select_1.MGAIN3 = (mgain >> 3) & 1; - update(Register::SignalSelect1); + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; - map.r.signal_select_2.INL = 0b01; // Lch input signal = LIN2 - map.r.signal_select_2.INR = 0b01; // Rch input signal = RIN2 - map.r.signal_select_2.MICL = 0; // MPWR = 2.4V - update(Register::SignalSelect2); + case 9: // ALC-> on, (-06dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz + Pre-amp Mic (+21dB=original) + map.r.alc_mode_control_2.REF = 0x90; // REF7-0 bits,max gain at ALC recovery operation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, 90H=-06dBs) + map.r.l_ch_input_volume_control.IV = 0x90; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0x90; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s -// map.r.r_ch_mic_gain_setting.MGR = 0x80; // Microphone sensitivity correction = 0dB. -// update(Register::RchMicGainSetting); -/* - map.r.timer_select.FRN = ?; - map.r.timer_select.FRATT = ?; - map.r.timer_select.ADRST = 0b??; - update(Register::TimerSelect); + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; - map.r.alc_timer_select. = ?; - update(Register::ALCTimerSelect); - map.r.alc_mode_control_1. = ?; - map.r.alc_mode_control_1.ALC = 1; + case 10: // ALC-> on, (-09dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz - Pre-amp MIC -3dB (18dB's) + // Reduce also Pre-amp Mic -3dB's (+18dB's) + mgain = 0b0110; // Pre-amp mic Mic Gain Pre-amp (+18dB), Original=0b0111 (+21dB's =7x3dBs), + + map.r.alc_mode_control_2.REF = 0x88; // REF7-0 bits,max gain at ALC recovery operation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, 88H=-09dBs) + map.r.l_ch_input_volume_control.IV = 0x88; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0x88; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + + case 11: // ALC-> on, (-12dB's) Auto Vol max + Wind Noise cancel + LPF 6kHz - Pre-amp MIC -6dB (15dB's) + // Reduce also Pre-amp Mic -6dB's (+15dB's) + mgain = 0b0101; // Pre-amp mic Mic Gain Pre-amp (+15dB), (Original=0b0111 (+21dB's= 7x3dBs), + + map.r.alc_mode_control_2.REF = 0x80; // REF7-0 bits,max gain at ALC recovery operation,(FFH +36dBs , D0H +18dBs, A0H 0dBs, 80H=-12dBs) + map.r.l_ch_input_volume_control.IV = 0x80; // Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + map.r.r_ch_input_volume_control.IV = 0x80; // Right Input Dig Vol Setting, same comment as above , Then value of IVOL should be <= than REF’s + + // Already Pre-loaded, "map.r.lpf_coefficient", 6Khz - LPF 1st Order from digital Block,Fc=6000Hz,fs = 48khz + // LPF bit is activated down, for all ALC digital modes. + break; + } + + //-------------------------------DIGITAL ALC (Automatic Level Control ) --- -------- + map.r.alc_mode_control_1.ALC = 0; // LMTH2-0, WTM1-0, RGAIN2-0, REF7-0, RFST1-0, EQFC1-0, FRATT, FRN and ALCEQN bits (needs to be set up with ALC disable = 0) update(Register::ALCModeControl1); - map.r.alc_mode_control_2.REF = ?; + map.r.timer_select.FRN = 0; // (FRN= 0 Fast Recovery mode , enable ) + map.r.timer_select.FRATT = 0; // Fast Recovery Ref. Volume Atten. Amount -0,00106dB's, timing 4/fs (default) + map.r.timer_select.ADRST = 0b00; // initial offset ADC cycles , 22ms @fs=48Khz. + update(Register::TimerSelect); + + map.r.alc_timer_select.RFST = 0b00; // RFST1-0: ALC Fast Recovery Speed Default: “00” (0.0032dB) + map.r.alc_timer_select.WTM = 0b00; // ALC Recovery Operation Waiting Period 128/fs = 2,7 mseg (min=default) + map.r.alc_timer_select.EQFC = 0b10; // Selecting default, fs 48Khz , ALCEQ: First order zero pole high pass filter fc2=100Hz, fc1=150Hz + map.r.alc_timer_select.IVTM = 0; // IVTM bit set the vol transition time ,236/fs = 4,9msecs (min) (default was 19,7msegs.) + update(Register::ALCTimerSelect); + + map.r.alc_mode_control_1.LMTH10 = 0b11; // ALC Limiter Detec Level/ Recovery Counter Reset; lower 2 bits (Ob111=-8,4dbs), (default 0b000=-2,5dBs) + map.r.alc_mode_control_1.RGAIN = 0b000; // ALC Recovery Gain Step, max step , max speed. Default: “000” (0.00424dB) + map.r.alc_mode_control_1.ALC = 1; // ALC Enable . (we are now, NOT in MANUAL volume mode, only becomes manual when (ALC=“0” while ADCPF=“1”. ) + map.r.alc_mode_control_1.LMTH2 = 1; // ALC Limiter Detection Level/ Recovery Counter Reset Level,Upper bit,default 0b000 + map.r.alc_mode_control_1.ALCEQN = 1; // ALC EQ Off =1 not used by now, 0: ALC EQ On (default) + update(Register::ALCModeControl1); + + // map.r.alc_mode_control_2.REF = 0x??; // Pre-loaded in top part. Maximum gain at ALC recovery operation,.(FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) update(Register::ALCModeControl2); -*/ -// map.r.l_ch_input_volume_control.IV = 0xe1; -// update(Register::LchInputVolumeControl); -// map.r.r_ch_input_volume_control.IV = 0xe1; -// update(Register::RchInputVolumeControl); -/* - map.r.auto_hpf_control.STG = 0b00; - map.r.auto_hpf_control.SENC = 0b011; - map.r.auto_hpf_control.AHPF = 0; - update(Register::AutoHPFControl); -*/ - map.r.digital_filter_select_1.HPFAD = 1; // HPF1 (after ADC) = on - map.r.digital_filter_select_1.HPFC = 0b11; // 2336.8 Hz @ fs=48k - update(Register::DigitalFilterSelect1); -/* - map.r.digital_filter_select_2.HPF = 0; - map.r.digital_filter_select_2.LPF = 0; - map.r.digital_filter_select_2.FIL3 = 0; - map.r.digital_filter_select_2.EQ0 = 0; - map.r.digital_filter_select_2.GN = 0b00; + + // map.r.l_ch_input_volume_control.IV = 0x??; // Pre-loaded in top part. Left, Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + update(Register::LchInputVolumeControl); + + // map.r.r_ch_input_volume_control.IV = 0x??; // Pre-loaded in top part. Right,Input Digital Volume Setting, (FFH +36dBs , D0H +18dBs, A0H 0dBs, 70H=-18dBs) + update(Register::RchInputVolumeControl); + + + //---------------Switch ON, Digital Automatic Wind Noise Filter reduction ------------------- + // Difficult to realise that Dynamic HPF Wind noise filter benefit, maybe because we have another fixed HPF 236.8 Hz . + // Anyway , we propose to activate it , with default setting conditions. + map.r.power_management_1.PMPFIL = 0; // (*1) To programm SENC, STG , we need PMPFIL = 0 . (but this disconnect Digital block power supply. + update(Register::PowerManagement1); // Updated PMPFIL to 0 . (*1) + + map.r.auto_hpf_control.STG = 0b00; // (00=LOW ATTENUATION Level), lets put 11 (HIGH ATTENUATION Level) (default 00) + map.r.auto_hpf_control.SENC = 0b011; // (000=LOW sensitivity detection)… 111((MAX sensitivity detection) (default 011) + map.r.auto_hpf_control.AHPF = 1; // Autom. Wind noise filter ON (AHPF bit=“1”).It atten. wind noise when detecting ,and adjusts the atten. level dynamically. + update(Register::AutoHPFControl); + + // We are in Digital Block ON , (Wind Noise Filter+ALC+LPF+EQ),==> needs at the end , PMPFIL=1 , Program. Dig.filter ON + // map.r.power_management_1.PMPFIL = 1; // that instruction is at the end , we can skp pre-loading Programmable Dig. filter ON (*1) + //--------------------------------------------------------------------- + + // Writing AUDIO PATH diagramm, Changing Audio mode path : Playback mode1 /-Recording mode2. (Figure 37 AK4951 datasheet, Table 27. Recording Playback Mode) + // When changing those modes, PMPFIL bit must be “0”, it is OK (*1) + map.r.digital_filter_mode.ADCPF = 1; // ADCPF bit swith ("0" Mic after ADC Output connected (recording mode) to the DIGITAL FILTER BLOCK. ("1" Playback mode) + map.r.digital_filter_mode.PFSDO = 1; // ADC (+ 1st order HPF) Output + map.r.digital_filter_mode.PFDAC = 0b00; // (Input selector for DAC (not used in MIC), SDTI= Audio Serial Data Input Pin) + update(Register::DigitalFilterMode); // Writing the Audio Path : NO DIGITAL BLOCK or DIG BLOCK FOR MIC , Audio mode path : Playback mode /-Recording mode. + + // The EQn (n=1, 2, 3, 4 or 5) coefficient must be set when EQn bit = “0” or PMPFIL bit = “0”., but we are already (*1) + // map.r.power_management_1.PMPFIL = 0; // In the previous Wind Noise Filter , we already set up PPFIL = 0 + // update(Register::PowerManagement1); // Activating the Power management of the used blocks . (Mic ADC always + Dig Block filter , when used ) + + // ... Set EQ & LPF coefficients --------------------------------- + + // writting to the IC ak4951 reg. settings defined in Ak4951.hpp , the 30 bytes , EQ coefficient = 5 (EQ1,2,3,4,5) x 3 (A,B,C coefficients) x 2 bytes (16 bits) + update(Register::E1Coefficient0); // we could pre-load here,ex ,"map.r.e1_coefficient_0.l = 0x50;" , EQ1 Coefficient A : A7...A0, but already done in ak4951.hpp + update(Register::E1Coefficient1); // we could pre-load here,ex ,"map.r.e1_coefficient_1.h = 0xFE;" , EQ1 Coefficient A : A15..A8, " " + update(Register::E1Coefficient2); // we could pre-load here,ex ,"map.r.e1_coefficient_2.l = 0x29;" , EQ1 Coefficient B : B7...B0, " " + update(Register::E1Coefficient3); // we could pre-load here,ex ,"map.r.e1_coefficient_3.h = 0xC5;" , EQ1 Coefficient B : B15..B8, " " + update(Register::E1Coefficient4); // we could pre-load here,ex ,"map.r.e1_coefficient_4.l = 0xA0;" , EQ1 Coefficient C : C7...C0, " " + update(Register::E1Coefficient5); // we could pre-load here,ex ,"map.r.e1_coefficient_5.h = 0x1C;" , EQ1 Coefficient C : C15..C8, " " + + update(Register::E2Coefficient0); // writing pre-loaded EQ2 coefficcients + update(Register::E2Coefficient1); + update(Register::E2Coefficient2); + update(Register::E2Coefficient3); + update(Register::E2Coefficient4); + update(Register::E2Coefficient5); + + // Already pre-loaded LPF coefficients to 6k, 3,5k or 4k ,(LPF 6Khz all digital alc modes top , except when 3k5 , 4k) + update(Register::LPFCoefficient0); // Writing pre-loaded 4 bytes LPF CoefFiecients 14 bits (FSA13..0, FSB13..0 + update(Register::LPFCoefficient1); + update(Register::LPFCoefficient2); + update(Register::LPFCoefficient3); + + // Activating LPF block , (and re-configuring the rest of bits of the same register) + map.r.digital_filter_select_2.HPF = 0; // HPF2-Block, Coeffic Setting Enable (OFF-Default), When HPF bit is “0”, audio data passes the HPF2 block by is 0dB gain. + map.r.digital_filter_select_2.LPF = 1; // LPF-Block, Coeffic Setting Enable (OFF-Default), When LPF bit is “0”, audio data passes the LPF block by 0dB gain. + map.r.digital_filter_select_2.FIL3 = 0; // Stereo_Emphasis_Filter-Block,(OFF-Default) Coefficient Setting Enable , OFF , Disable. + map.r.digital_filter_select_2.EQ0 = 0; // Gain Compensation-Block, (OFF-Default) Coeffic Setting Enable, When EQ0 bit = “0” audio data passes the EQ0 block by 0dB gain. + map.r.digital_filter_select_2.GN = 0b00; // Gain Setting of the Gain Compensation Block Default: “00”-Default (0dB) update(Register::DigitalFilterSelect2); - map.r.digital_filter_select_3.EQ1 = 0; - map.r.digital_filter_select_3.EQ2 = 0; - map.r.digital_filter_select_3.EQ3 = 0; - map.r.digital_filter_select_3.EQ4 = 0; - map.r.digital_filter_select_3.EQ5 = 0; - update(Register::DigitalFilterSelect3); -*/ - map.r.digital_filter_mode.PFSDO = 0; // ADC (+ 1st order HPF) Output - map.r.digital_filter_mode.ADCPF = 1; // ADC Output (default) - update(Register::DigitalFilterMode); - - // ... Set coefficients ... - - map.r.power_management_1.PMADL = 1; // ADC Lch = Lch input signal - map.r.power_management_1.PMADR = 1; // ADC Rch = Rch input signal - map.r.power_management_1.PMPFIL = 0; // Programmable filter unused, routed around. - update(Register::PowerManagement1); + // Acitivating digital block , power supply + map.r.power_management_1.PMADL = 1; // ADC Lch = Lch input signal. Mic Amp Lch and ADC Lch Power Management + map.r.power_management_1.PMADR = 1; // ADC Rch = Rch input signal. Mic Amp Rch and ADC Rch Power Management + map.r.power_management_1.PMPFIL = 1; // Pre-loaded in top part. Orig value=0, Programmable Digital filter unused (not power up), routed around. + update(Register::PowerManagement1); // Activating the Power management of the used blocks . (Mic ADC always + Dig Block filter , when used ) // 1059/fs, 22ms @ 48kHz chThdSleepMilliseconds(22); + + } + + // Common part for all alc_mode , -------------------------- + // const uint_fast8_t mgain = 0b0111; // Already pre-loaded , in above switch case . + map.r.signal_select_1.MGAIN20 = mgain & 7; // writing 3 lower bits of mgain , (pre-amp mic gain). + map.r.signal_select_1.PMMP = 1; // Activating DC Mic Power supply through 2kohms res., similar majority smartphones headphone+mic jack, "plug-in-power" + map.r.signal_select_1.MPSEL = 1; // MPWR2 pin ,selecting output voltage to MPWR2 pin, that we are using in portapack ext. MIC) + map.r.signal_select_1.MGAIN3 = (mgain >> 3) & 1; // writing 4th upper bit of mgain (pre-amp mic gain). + update(Register::SignalSelect1); + } + + void AK4951::microphone_disable() { - map.r.power_management_1.PMADL = 0; - map.r.power_management_1.PMADR = 0; - map.r.power_management_1.PMPFIL = 0; + map.r.power_management_1.PMADL = 0; // original code , disable Power managem.Mic ADC L + map.r.power_management_1.PMADR = 0; // original code , disable Power managem.Mic ADC R + map.r.power_management_1.PMPFIL = 0; // original code , disable Power managem. all Programmable Dig. block update(Register::PowerManagement1); - map.r.alc_mode_control_1.ALC = 0; + map.r.alc_mode_control_1.ALC = 0; // original code , Restore , disable ALC block. update(Register::ALCModeControl1); + + map.r.auto_hpf_control.AHPF = 0; //----------- new code addition , Restore disable Wind noise filter OFF (AHPF bit=“0”). + update(Register::AutoHPFControl); + + //Restore original AUDIO PATH , condition, (Digital filter block PATH is BY PASSED) (we can also swith off DIG. BLOCK power , PMPFIL=0) + // The Path in Recording Mode 2 & Playback Mode 2 , (NO DIG FILTER BLOCK AT ALL, not for MIC recording, nor for Playback) + map.r.digital_filter_mode.ADCPF = 1; // new code addition , ADCPF bit swith ("0" Mic after ADC Output connected (recording mode) to the DIGITAL FILTER BLOCK. ("1" Playback mode) + map.r.digital_filter_mode.PFSDO = 0; // new code addition , ADC bit switch ("0" : 1st order HPF) connectedto the Output. By bass DIGITAL block . + map.r.digital_filter_mode.PFDAC = 0b00; // new code addition , (Input selector for DAC (not used in MIC), SDTI= Audio Serial Data Input Pin) + update(Register::DigitalFilterMode); // Writing the Audio Path : NO DIGITAL BLOCK or DIG BLOCK FOR MIC , Audio mode path : Playback mode /-Recording mode. + + // Restore original condition , LPF , OFF . same as when not using DIGITAL Programmable block + map.r.digital_filter_select_2.LPF = 0; // LPF-Block, Coeffic Setting Enable (OFF-Default), When LPF bit is “0”, audio data passes the LPF block by 0dB gain. + update(Register::DigitalFilterSelect2); + + map.r.lpf_coefficient_0.l = 0x00; // Pre-loading here LPF 6k , 1st Order from digital Block , Fc=6000 Hz, fs = 48khz + map.r.lpf_coefficient_1.h = 0x00; // LPF bit is activated down, for all ALC digital modes. + map.r.lpf_coefficient_2.l = 0x00; // Writting reg to AK4951 , down with update.... + map.r.lpf_coefficient_3.h = 0x00; + + update(Register::LPFCoefficient0); // Writing pre-loaded 4 bytes LPF CoefFiecients 14 bits (FSA13..0, FSB13..0 + update(Register::LPFCoefficient1); + update(Register::LPFCoefficient2); + update(Register::LPFCoefficient3); + + // Switch off all EQ 1,2,3,4,5 + map.r.digital_filter_select_3.EQ1 = 0; // EQ1 Coeffic Setting , (0: Disable-default, audio data passes EQ1 block by 0dB gain). When EQ1="1”, the settings of E1A15-0, E1B15-0 and E1C15-0 bits are enabled + map.r.digital_filter_select_3.EQ2 = 0; // EQ2 Coeffic Setting , (0: Disable-default, audio data passes EQ2 block by 0dB gain). When EQ2="1”, the settings of E2A15-0, E2B15-0 and E2C15-0 bits are enabled + map.r.digital_filter_select_3.EQ3 = 0; // EQ3 Coeffic Setting , (0: Disable-default, audio data passes EQ3 block by 0dB gain). When EQ3="1”, the settings of E3A15-0, E3B15-0 and E3C15-0 bits are enabled + map.r.digital_filter_select_3.EQ4 = 0; // EQ4 Coeffic Setting , (0: Disable-default, audio data passes EQ4 block by 0dB gain). When EQ4="1”, the settings of E4A15-0, E4B15-0 and E4C15-0 bits are enabled + map.r.digital_filter_select_3.EQ5 = 0; // EQ5 Coeffic Setting , (0: Disable-default, audio data passes EQ5 block by 0dB gain). When EQ5="1”, the settings of E5A15-0, E5B15-0 and E5C15-0 bits are enabled + update(Register::DigitalFilterSelect3); + } reg_t AK4951::read(const address_t reg_address) { diff --git a/firmware/common/ak4951.hpp b/firmware/common/ak4951.hpp index ab7d3b81..ea394966 100644 --- a/firmware/common/ak4951.hpp +++ b/firmware/common/ak4951.hpp @@ -773,40 +773,41 @@ constexpr RegisterMap default_after_reset { Register_Type { .REV = 0b1100, }, - .e1_coefficient_0 = { .l = 0x00 }, - .e1_coefficient_1 = { .h = 0x00 }, - .e1_coefficient_2 = { .l = 0x00 }, - .e1_coefficient_3 = { .h = 0x00 }, - .e1_coefficient_4 = { .l = 0x00 }, - .e1_coefficient_5 = { .h = 0x00 }, + // just pre-loading into memory, 30 bytes = EQ 1,2,3,4,5 x A,B,C (2 x bytes) coefficients, but it will be written from ak4951.cpp + .e1_coefficient_0 = { .l = 0xCA }, //EQ1 Coefficient A : A7...A0, BW : 300Hz - 1700Hz (fo = 1150Hz , fb= 1700Hz) , k=1,8 peaking + .e1_coefficient_1 = { .h = 0x05 }, //EQ1 Coefficient A : A15..A8 + .e1_coefficient_2 = { .l = 0xEB }, //EQ1 Coefficient B : B7...B0 + .e1_coefficient_3 = { .h = 0x38 }, //EQ1 Coefficient B : B15...B8 + .e1_coefficient_4 = { .l = 0x6F }, //EQ1 Coefficient C : C7...C0 + .e1_coefficient_5 = { .h = 0xE6 }, //EQ1 Coefficient C : C15..C8 - .e2_coefficient_0 = { .l = 0x00 }, - .e2_coefficient_1 = { .h = 0x00 }, - .e2_coefficient_2 = { .l = 0x00 }, - .e2_coefficient_3 = { .h = 0x00 }, - .e2_coefficient_4 = { .l = 0x00 }, - .e2_coefficient_5 = { .h = 0x00 }, + .e2_coefficient_0 = { .l = 0x05 }, //EQ2 Coefficient A : A7...A0, BW : 250Hz - 2700Hz (fo = 1475Hz , fb= 2450Hz) , k=1,8 peaking + .e2_coefficient_1 = { .h = 0x08 }, //EQ2 Coefficient A : A15..A8 + .e2_coefficient_2 = { .l = 0x11 }, //EQ2 Coefficient B : B7...B0 + .e2_coefficient_3 = { .h = 0x36 }, //EQ2 Coefficient B : B15...B8 + .e2_coefficient_4 = { .l = 0xE9 }, //EQ2 Coefficient C : C7...C0 + .e2_coefficient_5 = { .h = 0xE8 }, //EQ2 Coefficient C : C15..C8 - .e3_coefficient_0 = { .l = 0x00 }, - .e3_coefficient_1 = { .h = 0x00 }, - .e3_coefficient_2 = { .l = 0x00 }, - .e3_coefficient_3 = { .h = 0x00 }, - .e3_coefficient_4 = { .l = 0x00 }, - .e3_coefficient_5 = { .h = 0x00 }, + .e3_coefficient_0 = { .l = 0x00 }, //EQ3 Coefficient A : A7...A0, not used currently + .e3_coefficient_1 = { .h = 0x00 }, //EQ3 Coefficient A : A15..A8 + .e3_coefficient_2 = { .l = 0x00 }, //EQ3 Coefficient B : B7...B0 + .e3_coefficient_3 = { .h = 0x00 }, //EQ3 Coefficient B : B15...B8 + .e3_coefficient_4 = { .l = 0x00 }, //EQ3 Coefficient C : C7...C0 + .e3_coefficient_5 = { .h = 0x00 }, //EQ3 Coefficient C : C15..C8 - .e4_coefficient_0 = { .l = 0x00 }, - .e4_coefficient_1 = { .h = 0x00 }, - .e4_coefficient_2 = { .l = 0x00 }, - .e4_coefficient_3 = { .h = 0x00 }, - .e4_coefficient_4 = { .l = 0x00 }, - .e4_coefficient_5 = { .h = 0x00 }, + .e4_coefficient_0 = { .l = 0x00 }, //EQ4 Coefficient A : A7...A0, not used currently + .e4_coefficient_1 = { .h = 0x00 }, //EQ4 Coefficient A : A15..A8 + .e4_coefficient_2 = { .l = 0x00 }, //EQ4 Coefficient B : B7...B0 + .e4_coefficient_3 = { .h = 0x00 }, //EQ4 Coefficient B : B15...B8 + .e4_coefficient_4 = { .l = 0x00 }, //EQ4 Coefficient C : C7...C0 + .e4_coefficient_5 = { .h = 0x00 }, //EQ4 Coefficient C : C15..C8 - .e5_coefficient_0 = { .l = 0x00 }, - .e5_coefficient_1 = { .h = 0x00 }, - .e5_coefficient_2 = { .l = 0x00 }, - .e5_coefficient_3 = { .h = 0x00 }, - .e5_coefficient_4 = { .l = 0x00 }, - .e5_coefficient_5 = { .h = 0x00 }, + .e5_coefficient_0 = { .l = 0x00 }, //EQ5 Coefficient A : A7...A0, not used currently + .e5_coefficient_1 = { .h = 0x00 }, //EQ5 Coefficient A : A15..A8 + .e5_coefficient_2 = { .l = 0x00 }, //EQ5 Coefficient B : B7...B0 + .e5_coefficient_3 = { .h = 0x00 }, //EQ5 Coefficient B : B15...B8 + .e5_coefficient_4 = { .l = 0x00 }, //EQ5 Coefficient C : C7...C0 + .e5_coefficient_5 = { .h = 0x00 }, //EQ5 Coefficient C : C15..C8 } }; class AK4951 : public audio::Codec { @@ -839,7 +840,7 @@ public: void set_headphone_volume(const volume_t volume) override; void headphone_mute(); - void microphone_enable(); + void microphone_enable(int8_t alc_mode); // added user GUI parameter , to set up AK4951 ALC mode. void microphone_disable(); size_t reg_count() const override { diff --git a/firmware/common/wm8731.hpp b/firmware/common/wm8731.hpp index a5c8908b..ac164a04 100644 --- a/firmware/common/wm8731.hpp +++ b/firmware/common/wm8731.hpp @@ -345,8 +345,9 @@ public: void speaker_disable() {}; - void microphone_enable() override { - // TODO: Implement + void microphone_enable(int8_t alc_mode) override { + (void)alc_mode; // to avoid "unused warning" when compiling. (@WM8731 we do not use that parameter) + // TODO: Implement, } void microphone_disable() override {