Reticulum/docs/manual/_sources/interfaces.rst.txt

.. _interfaces-main:

********************
Supported Interfaces
********************

Reticulum supports using many kinds of devices as networking interfaces, and
allows you to mix and match them in any way you choose. The number of distinct
network topologies you can create with Reticulum is more or less endless, but
common to them all is that you will need to define one or more *interfaces*
for Reticulum to use.

The following sections describe the interfaces currently available in Reticulum,
and gives example configurations for the respective interface types.

.. _interfaces-udp:

UDP Interface
=============

A UDP interface can be useful for communicating over IP networks, both
private and the internet. It can also allow broadcast communication
over IP networks, so it can provide an easy way to enable connectivity
with all other peers on a local area network.

The below example is enabled by default on new Reticulum installations,
as it provides an easy way to get started and to test Reticulum on a
pre-existing LAN.

.. code::

  # This example enables communication with other
  # local Reticulum peers over UDP.
  
  [[Default UDP Interface]]
    type = UDPInterface
    interface_enabled = True
    outgoing = True
    listen_ip = 0.0.0.0
    listen_port = 4242
    forward_ip = 255.255.255.255
    forward_port = 4242

    # The above configuration will allow communication
    # within the local broadcast domains of all local
    # IP interfaces. This is enabled by default as an
    # easy way to get started, but you might want to
    # consider altering it to something more specific.

    # Instead of specifying listen_ip, listen_port,
    # forward_ip and forward_port, you can also bind
    # to a specific network device like below.

    # device = eth0
    # port = 4242

    # Assuming the eth0 device has the address
    # 10.55.0.72/24, the above configuration would
    # be equivalent to the following manual setup.
    # Note that we are both listening and forwarding to
    # the broadcast address of the network segments.

    # listen_ip = 10.55.0.255
    # listen_port = 4242
    # forward_ip = 10.55.0.255
    # forward_port = 4242

    # You can of course also communicate only with
    # a single IP address

    # listen_ip = 10.55.0.15
    # listen_port = 4242
    # forward_ip = 10.55.0.16
    # forward_port = 4242

.. _interfaces-tcps:

TCP Server Interface
====================

The TCP Server interface is suitable for allowing other peers to connect over
the Internet or private IP networks. When a TCP server interface has been
configured, other Reticulum peers can connect to it with a TCP Client interface.

.. code::

  # This example demonstrates a TCP server interface.
  # It will listen for incoming connections on the
  # specified IP address and port number.
  
  [[TCP Server Interface]]
    type = TCPServerInterface
    interface_enabled = True
    outgoing = True

    # This configuration will listen on all IP
    # interfaces on port 4242
    
    listen_ip = 0.0.0.0
    listen_port = 4242

    # Alternatively you can bind to a specific IP
    
    # listen_ip = 10.0.0.88
    # listen_port = 4242

    # Or a specific network device
    
    # device = eth0
    # port = 4242


.. _interfaces-tcpc:

TCP Client Interface
====================

To connect to a TCP server interface, you would naturally use the TCP client
interface. Many TCP Client interfaces from different peers can connect to the
same TCP Server interface at the same time.

.. code::

  # Here's an example of a TCP Client interface. The
  # target_host can either be an IP address or a hostname.

  [[TCP Client Interface]]
    type = TCPClientInterface
    interface_enabled = True
    outgoing = True
    target_host = 127.0.0.1
    target_port = 4242


.. _interfaces-rnode:

RNode LoRa Interface
====================

To use Reticulum over LoRa, the `RNode <https://unsigned.io/rnode/>`_ interface
can be used, and offers full control over LoRa parameters.

.. code::

  # Here's an example of how to add a LoRa interface
  # using the RNode LoRa transceiver.

  [[RNode LoRa Interface]]
    type = RNodeInterface

    # Enable interface if you want use it!
    interface_enabled = True

    # Allow transmit on interface. Setting
    # this to false will create a listen-
    # only interface.
    outgoing = true

    # Serial port for the device
    port = /dev/ttyUSB0

    # Set frequency to 867.2 MHz
    frequency = 867200000

    # Set LoRa bandwidth to 125 KHz
    bandwidth = 125000

    # Set TX power to 7 dBm (5 mW)
    txpower = 7

    # Select spreading factor 8. Valid 
    # range is 7 through 12, with 7
    # being the fastest and 12 having
    # the longest range.
    spreadingfactor = 8

    # Select coding rate 5. Valid range
    # is 5 throough 8, with 5 being the
    # fastest, and 8 the longest range.
    codingrate = 5

    # You can configure the RNode to send
    # out identification on the channel with
    # a set interval by configuring the
    # following two parameters.
    # id_callsign = MYCALL-0
    # id_interval = 600

    # For certain homebrew RNode interfaces
    # with low amounts of RAM, using packet
    # flow control can be useful. By default
    # it is disabled.
    flow_control = False

.. _interfaces-serial:

Serial Interface
================

Reticulum can be used over serial ports directly, or over any device with a
serial port, that will transparently pass data. Useful for communicating
directly over a wire-pair, or for using devices such as data radios and lasers.

.. code::

  [[Serial Interface]]
    type = SerialInterface
    interface_enabled = True
    outgoing = True

    # Serial port for the device
    port = /dev/ttyUSB0

    # Set the serial baud-rate and other
    # configuration parameters.
    speed = 115200
    databits = 8
    parity = none
    stopbits = 1

.. _interfaces-kiss:

KISS Interface
==============

With the KISS interface, you can use Reticulum over a variety of packet
radio modems and TNCs, including `OpenModem <https://unsigned.io/openmodem/>`_.
KISS interfaces can also be configured to periodically send out beacons
for station identification purposes.

.. code::

  [[Packet Radio KISS Interface]]
    type = KISSInterface
    interface_enabled = True
    outgoing = true

    # Serial port for the device
    port = /dev/ttyUSB1

    # Set the serial baud-rate and other
    # configuration parameters.
    speed = 115200    
    databits = 8
    parity = none
    stopbits = 1

    # Set the modem preamble.
    preamble = 150

    # Set the modem TX tail.
    txtail = 10

    # Configure CDMA parameters. These
    # settings are reasonable defaults.
    persistence = 200
    slottime = 20

    # You can configure the interface to send
    # out identification on the channel with
    # a set interval by configuring the
    # following two parameters. The KISS
    # interface will only ID if the set
    # interval has elapsed since it's last
    # actual transmission. The interval is
    # configured in seconds.
    # This option is commented out and not
    # used by default.
    # id_callsign = MYCALL-0
    # id_interval = 600

    # Whether to use KISS flow-control.
    # This is useful for modems that have
    # a small internal packet buffer, but
    # support packet flow control instead.
    flow_control = false

.. _interfaces-ax25:

AX.25 KISS Interface
====================

If you're using Reticulum on amateur radio spectrum, you might want to
use the AX.25 KISS interface. This way, Reticulum will automatically
encapsulate it's traffic in AX.25 and also identify your stations
transmissions with your callsign and SSID. 

Only do this if you really need to! Reticulum doesn't need the AX.25
layer for anything, and it incurs extra overhead on every packet to
encapsulate in AX.25.

A more efficient way is to use the plain KISS interface with the
beaconing functionality described above.

.. code::

  [[Packet Radio AX.25 KISS Interface]]
    type = AX25KISSInterface

    # Set the station callsign and SSID
    callsign = NO1CLL
    ssid = 0

    # Enable interface if you want use it!
    interface_enabled = True

    # Allow transmit on interface.
    outgoing = True

    # Serial port for the device
    port = /dev/ttyUSB2

    # Set the serial baud-rate and other
    # configuration parameters.
    speed = 115200    
    databits = 8
    parity = none
    stopbits = 1

    # Set the modem preamble. A 150ms
    # preamble should be a reasonable
    # default, but may need to be
    # increased for radios with slow-
    # opening squelch and long TX/RX
    # turnaround
    preamble = 150

    # Set the modem TX tail. In most
    # cases this should be kept as low
    # as possible to not waste airtime.
    txtail = 10

    # Configure CDMA parameters. These
    # settings are reasonable defaults.
    persistence = 200
    slottime = 20

    # Whether to use KISS flow-control.
    # This is useful for modems with a
    # small internal packet buffer.
    flow_control = false