mirror of
https://github.com/markqvist/Reticulum.git
synced 2024-12-20 21:34:20 -05:00
264 lines
10 KiB
ReStructuredText
264 lines
10 KiB
ReStructuredText
.. _hardware-main:
|
|
|
|
***********************
|
|
Communications Hardware
|
|
***********************
|
|
|
|
One of the truly valuable aspects of Reticulum is the ability to use it over
|
|
almost any conceivable kind of communications medium. The :ref:`interface types<interfaces-main>`
|
|
available for configuration in Reticulum are flexible enough to cover the use
|
|
of most wired and wireless communications hardware available, from decades-old
|
|
packet radio modems to modern millimeter-wave backhaul systems.
|
|
|
|
If you already have or operate some kind of communications hardware, there is a
|
|
very good chance that it will work with Reticulum out of the box. In case it does
|
|
not, it is possible to provide the necessary glue with very little effort using
|
|
for example the :ref:`PipeInterface<interfaces-pipe>` or the :ref:`TCPClientInterface<interfaces-tcpc>`
|
|
in combination with code like `TCP KISS Server <https://github.com/simplyequipped/tcpkissserver>`_
|
|
by `simplyequipped <https://github.com/simplyequipped>`_.
|
|
|
|
While this broad support and flexibility is very useful, an abundance of options
|
|
can sometimes make it difficult to know where to begin, especially when you are
|
|
starting from scratch.
|
|
|
|
This chapter will outline a few different sensible starting paths to get
|
|
real-world functional wireless communications up and running with minimal cost
|
|
and effort. Two fundamental devices categories will be covered, *RNodes* and
|
|
*WiFi-based radios*. Additionally, other common options will be briefly described.
|
|
|
|
Knowing how to employ just a few different types of hardware will make it possible
|
|
to build a wide range of useful networks with little effort.
|
|
|
|
Combining Hardware Types
|
|
========================
|
|
|
|
It is useful to combine different link and hardware types when designing and
|
|
building a network. One useful design pattern is to employ high-capacity point-to-point
|
|
links based on WiFi or millimeter-wave radios (with high-gain directional antennas)
|
|
for the network backbone, and using LoRa-based RNodes for covering large areas with
|
|
connectivity for client devices.
|
|
|
|
|
|
.. _rnode-main:
|
|
|
|
RNode
|
|
=====
|
|
|
|
Reliable and general-purpose long-range digital radio transceiver systems are
|
|
commonly either very expensive, difficult to set up and operate, hard to source,
|
|
power-hungry, or all of the above at the same time. In an attempt to alleviate
|
|
this situation, the transceiver system *RNode* was designed. It is important to
|
|
note that RNode is not one specific device, from one particular vendor, but
|
|
*an open plaform* that anyone can use to build interoperable digital transceivers
|
|
suited to their needs and particular situations.
|
|
|
|
An RNode is a general purpose, interoperable, low-power and long-range, reliable,
|
|
open and flexible radio communications device. Depending on its components, it can
|
|
operate on many different frequency bands, and use many different modulation
|
|
schemes, but most commonly, and for the purposes of this chapter, we will limit
|
|
the discussion to RNodes using *LoRa* modulation in common ISM bands.
|
|
|
|
**Avoid Confusion!** RNodes can use LoRa as a *physical-layer modulation*, but it
|
|
does not use, and has nothing to do with the *LoRaWAN* protocol and standard, commonly
|
|
used for centrally controlled IoT devices. RNodes use *raw LoRa modulation*, without
|
|
any additional protocol overhead. All high-level protocol functionality is handled
|
|
directly by Reticulum.
|
|
|
|
.. _rnode-creating:
|
|
|
|
Creating RNodes
|
|
^^^^^^^^^^^^^^^
|
|
RNode has been designed as a system that is easy to replicate across time and
|
|
space. You can put together a functioning transceiver using commonly available
|
|
components, and a few open source software tools. While you can design and build RNodes
|
|
completely from scratch, to your exact desired specifications, this chapter
|
|
will explain the easiest possible approach to creating RNodes: Using common
|
|
LoRa development boards. This approach can be boiled down to two simple steps:
|
|
|
|
1. Obtain one or more supported development boards
|
|
2. Install the RNode firmware with the automated installer
|
|
|
|
Once the firmware has been installed and provisioned by the install script, it
|
|
is ready to use with any software that supports RNodes, including Reticulum.
|
|
The device can be used with Reticulum by adding an :ref:`RNodeInterface<interfaces-rnode>`
|
|
to the configuration.
|
|
|
|
.. _rnode-supported:
|
|
|
|
Supported Boards
|
|
^^^^^^^^^^^^^^^^
|
|
To create one or more RNodes, you will need to obtain supported development
|
|
boards. The following boards are supported by the auto-installer.
|
|
|
|
LilyGO LoRa32 v2.1
|
|
""""""""""""""""""
|
|
.. image:: graphics/board_t3v21.png
|
|
:width: 46%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x & v2.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** ESP32
|
|
- **Manufacturer** `LilyGO <https://lilygo.cn>`_
|
|
|
|
|
|
LilyGO LoRa32 v2.0
|
|
""""""""""""""""""
|
|
.. image:: graphics/board_t3v20.png
|
|
:width: 46%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x & v2.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** ESP32
|
|
- **Manufacturer** `LilyGO <https://lilygo.cn>`_
|
|
|
|
|
|
LilyGO T-Beam
|
|
"""""""""""""
|
|
.. image:: graphics/board_tbeam.png
|
|
:width: 75%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x & v2.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** ESP32
|
|
- **Manufacturer** `LilyGO <https://lilygo.cn>`_
|
|
|
|
|
|
Heltec LoRa32 v2.0
|
|
""""""""""""""""""
|
|
.. image:: graphics/board_heltec32.png
|
|
:width: 58%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x & v2.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** ESP32
|
|
- **Manufacturer** `Heltec Automation <https://heltec.org>`_
|
|
|
|
|
|
Unsigned RNode v2.x
|
|
"""""""""""""""""""
|
|
.. image:: graphics/board_rnodev2.png
|
|
:width: 58%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x & v2.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** ESP32
|
|
- **Manufacturer** `unsigned.io <https://unsigned.io>`_
|
|
|
|
|
|
Unsigned RNode v1.x
|
|
"""""""""""""""""""
|
|
.. image:: graphics/board_rnode.png
|
|
:width: 50%
|
|
:align: center
|
|
|
|
- **Supported Firmware Lines** v1.x
|
|
- **Transceiver IC** Semtech SX1276
|
|
- **Device Platform** AVR ATmega1284p
|
|
- **Manufacturer** `unsigned.io <https://unsigned.io>`_
|
|
|
|
|
|
.. _rnode-installation:
|
|
|
|
Installation
|
|
^^^^^^^^^^^^
|
|
|
|
Once you have obtained compatible boards, you can install the `RNode Firmware <https://github.com/markqvist/RNode_Firmware>`_
|
|
using the `RNode Configuration Utility <https://github.com/markqvist/rnodeconfigutil>`_.
|
|
If you have installed Reticulum on your system, the ``rnodeconf`` program will already be
|
|
available. If not, make sure that ``Python3`` and ``pip`` is installed on your system, and
|
|
then install Reticulum with with ``pip``:
|
|
|
|
.. code::
|
|
|
|
pip install rns
|
|
|
|
Once installation has completed, it is time to start installing the firmware on your
|
|
devices. Run ``rnodeconf`` in auto-install mode like so:
|
|
|
|
.. code::
|
|
|
|
rnodeconf --autoinstall
|
|
|
|
The utility will guide you through the installation process by asking a series of
|
|
questions about your hardware. Simply follow the guide, and the utility will
|
|
auto-install and configure your devices.
|
|
|
|
.. _rnode-usage:
|
|
|
|
Usage with Reticulum
|
|
^^^^^^^^^^^^^^^^^^^^
|
|
When the devices have been installed and provisioned, you can use them with Reticulum
|
|
by adding the :ref:`relevant interface section<interfaces-rnode>` to the configuration
|
|
file of Reticulum. For v1.x firmwares, you will have to specify all interface parameters,
|
|
such as serial port and on-air parameters. For v2.x firmwares, you just need to specify
|
|
the Connection ID of the RNode, and Reticulum will automatically locate and connect to the
|
|
RNode, using the parameters stored in the RNode itself.
|
|
|
|
|
|
WiFi-based Hardware
|
|
===================
|
|
|
|
It is possible to use all kinds of both short- and long-range WiFi-based hardware
|
|
with Reticulum. Any kind of hardware that fully supports bridged Ethernet over the
|
|
WiFi interface will work with the :ref:`AutoInterface<interfaces-auto>` in Reticulum.
|
|
Most devices will behave like this by default, or allow it via configuration options.
|
|
|
|
This means that you can simply configure the physical links of the WiFi based devices,
|
|
and start communicating over them using Reticulum. It is not necessary to enable any IP
|
|
infrastructure such as DHCP servers, DNS or similar, as long as at least Ethernet is
|
|
available, and packets are passed transparently over the physical WiFi-based devices.
|
|
|
|
.. only:: html
|
|
|
|
.. image:: graphics/radio_rblhg5.png
|
|
:width: 49%
|
|
|
|
.. image:: graphics/radio_is5ac.png
|
|
:width: 49%
|
|
|
|
Below is a list of example WiFi (and similar) radios that work well for high capacity
|
|
Reticulum links over long distances:
|
|
|
|
- `Ubiquiti airMAX radios <https://store.ui.com/collections/operator-airmax-devices>`_
|
|
- `Ubiquiti LTU radios <https://store.ui.com/collections/operator-ltu>`_
|
|
- `MikroTik radios <https://mikrotik.com/products/group/wireless-systems>`_
|
|
|
|
This list is by no means exhaustive, and only serves as a few examples of radio hardware
|
|
that is relatively cheap while providing long range and high capacity for Reticulum
|
|
networks. As in all other cases, it is also possible for Reticulum to co-exist with IP
|
|
networks running concurrently on such devices.
|
|
|
|
Ethernet-based Hardware
|
|
=======================
|
|
|
|
Reticulum can run over any kind of hardware that can provide a switched Ethernet-based
|
|
medium. This means that anything from a plain Ethernet switch, to fiber-optic systems,
|
|
to data radios with Ethernet interfaces can be used by Reticulum.
|
|
|
|
The Ethernet medium does not need to have any IP infrastructure such as DHCP servers
|
|
or routing set up, but in case such infrastructure does exist, Reticulum will simply
|
|
co-exist with.
|
|
|
|
To use Reticulum over Ethernet-based mediums, it is generally enough to use the included
|
|
:ref:`AutoInterface<interfaces-auto>`. This interface also works over any kind of
|
|
virtual networking adapter, such as ``tun`` and ``tap`` devices in Linux.
|
|
|
|
Serial Lines & Devices
|
|
======================
|
|
|
|
Using Reticulum over any kind of raw serial line is also possible with the
|
|
:ref:`SerialInterface<interfaces-serial>`. This interface type is also useful for
|
|
using Reticulum over communications hardware that provides a serial port interface.
|
|
|
|
Packet Radio Modems
|
|
===================
|
|
|
|
Any packet radio modem that provides a standard KISS interface over USB, serial or TCP
|
|
can be used with Reticulum. This includes virtual software modems such as
|
|
`FreeDV TNC <https://github.com/xssfox/freedv-tnc>`_ and `Dire Wolf <https://github.com/wb2osz/direwolf>`_.
|