Added RNodeMultiInterface to documentation

docs/manual/_sources/interfaces.rst.txt

@@ -406,6 +406,121 @@ can be used, and offers full control over LoRa parameters.
     # airtime_limit_short = 33
 
 
+.. _interfaces-rnode-multi:
+
+RNode Multi Interface
+=====================
+
+For RNodes that support multiple LoRa transceivers, the RNode
+Multi interface can be used to configure sub-interfaces individually.
+
+.. code::
+
+  # Here's an example of how to add an RNode Multi interface
+  # using the RNode LoRa transceiver.
+
+  [[RNode Multi Interface]]
+  type = RNodeMultiInterface
+
+  # Enable interface if you want to use it!
+  interface_enabled = True
+
+  # Serial port for the device
+  port = /dev/ttyACM0
+
+  # You can configure the RNode to send
+  # out identification on the channel with
+  # a set interval by configuring the
+  # following two parameters.
+
+  # id_callsign = MYCALL-0
+  # id_interval = 600
+
+    # A subinterface
+    [[[HIGHDATARATE]]]
+    # Subinterfaces can be enabled and disabled in of themselves
+    interface_enabled = True
+
+    # Set frequency to 2.4GHz
+    frequency = 2400000000
+
+    # Set LoRa bandwidth to 1625 KHz
+    bandwidth = 1625000
+
+    # Set TX power to 0 dBm (0.12 mW)
+    txpower = 0
+
+    # The virtual port, only the manufacturer
+    # or the person who wrote the board config
+    # can tell you what it will be for which
+    # physical hardware interface
+    vport = 1
+
+    # Select spreading factor 5. Valid
+    # range is 5 through 12, with 5 
+    # being the fastest and 12 having
+    # the longest range.
+    spreadingfactor = 5
+
+    # Select coding rate 5. Valid range
+    # is 5 throough 8, with 5 being the
+    # fastest, and 8 the longest range.
+    codingrate = 5
+
+    # It is possible to limit the airtime
+    # utilisation of an RNode by using the
+    # following two configuration options.
+    # The short-term limit is applied in a
+    # window of approximately 15 seconds,
+    # and the long-term limit is enforced
+    # over a rolling 60 minute window. Both
+    # options are specified in percent.
+
+    # airtime_limit_long = 100
+    # airtime_limit_short = 100
+
+    [[[LOWDATARATE]]]
+    # Subinterfaces can be enabled and disabled in of themselves
+    interface_enabled = True
+
+    # Set frequency to 865.6 MHz
+    frequency = 865600000
+
+    # The virtual port, only the manufacturer
+    # or the person who wrote the board config
+    # can tell you what it will be for which
+    # physical hardware interface
+    vport = 0
+
+    # Set LoRa bandwidth to 125 KHz
+    bandwidth = 125000
+
+    # Set TX power to 0 dBm (0.12 mW)
+    txpower = 0
+
+    # Select spreading factor 7. Valid
+    # range is 5 through 12, with 5 
+    # being the fastest and 12 having
+    # the longest range.
+    spreadingfactor = 7
+
+    # Select coding rate 5. Valid range
+    # is 5 throough 8, with 5 being the
+    # fastest, and 8 the longest range.
+    codingrate = 5
+
+    # It is possible to limit the airtime
+    # utilisation of an RNode by using the
+    # following two configuration options.
+    # The short-term limit is applied in a
+    # window of approximately 15 seconds,
+    # and the long-term limit is enforced
+    # over a rolling 60 minute window. Both
+    # options are specified in percent.
+
+    # airtime_limit_long = 100
+    # airtime_limit_short = 100
+
 .. _interfaces-serial:
 
 Serial Interface

docs/manual/_sources/networks.rst.txt

@@ -60,7 +60,7 @@ with Reticulum:
 
  * | Reticulum is designed to work reliably in open, trustless environments. This
      means you can use it to create open-access networks, where participants can
-     join and leave in an free and unorganised manner. This property allows an
+     join and leave in a free and unorganised manner. This property allows an
      entirely new, and so far, mostly unexplored class of networked applications,
      where networks, and the information flow within them can form and dissolve
      organically.