mirror of
https://github.com/liberatedsystems/RNode_Firmware_CE.git
synced 2024-12-25 07:29:25 -05:00
882 lines
18 KiB
C++
882 lines
18 KiB
C++
// Copyright (c) Sandeep Mistry. All rights reserved.
|
|
// Licensed under the MIT license.
|
|
|
|
// Modifications and additions copyright 2023 by Mark Qvist
|
|
// Obviously still under the MIT license.
|
|
|
|
#include "sx128x.h"
|
|
#include "Boards.h"
|
|
|
|
#define MCU_1284P 0x91
|
|
#define MCU_2560 0x92
|
|
#define MCU_ESP32 0x81
|
|
#define MCU_NRF52 0x71
|
|
#if defined(__AVR_ATmega1284P__)
|
|
#define PLATFORM PLATFORM_AVR
|
|
#define MCU_VARIANT MCU_1284P
|
|
#elif defined(__AVR_ATmega2560__)
|
|
#define PLATFORM PLATFORM_AVR
|
|
#define MCU_VARIANT MCU_2560
|
|
#elif defined(ESP32)
|
|
#define PLATFORM PLATFORM_ESP32
|
|
#define MCU_VARIANT MCU_ESP32
|
|
#elif defined(NRF52840_XXAA)
|
|
#define PLATFORM PLATFORM_NRF52
|
|
#define MCU_VARIANT MCU_NRF52
|
|
#endif
|
|
|
|
#ifndef MCU_VARIANT
|
|
#error No MCU variant defined, cannot compile
|
|
#endif
|
|
|
|
#if MCU_VARIANT == MCU_ESP32
|
|
#if MCU_VARIANT == MCU_ESP32 and !defined(CONFIG_IDF_TARGET_ESP32S3)
|
|
#include "soc/rtc_wdt.h"
|
|
#endif
|
|
#define ISR_VECT IRAM_ATTR
|
|
#else
|
|
#define ISR_VECT
|
|
#endif
|
|
|
|
#define OP_RF_FREQ_8X 0x86
|
|
#define OP_SLEEP_8X 0x84
|
|
#define OP_STANDBY_8X 0x80
|
|
#define OP_TX_8X 0x83
|
|
#define OP_RX_8X 0x82
|
|
#define OP_SET_IRQ_FLAGS_8X 0x8D // also provides info such as
|
|
// preamble detection, etc for
|
|
// knowing when it's safe to switch
|
|
// antenna modes
|
|
#define OP_CLEAR_IRQ_STATUS_8X 0x97
|
|
#define OP_GET_IRQ_STATUS_8X 0x15
|
|
#define OP_RX_BUFFER_STATUS_8X 0x17
|
|
#define OP_PACKET_STATUS_8X 0x1D // get snr & rssi of last packet
|
|
#define OP_CURRENT_RSSI_8X 0x1F
|
|
#define OP_MODULATION_PARAMS_8X 0x8B // bw, sf, cr, etc.
|
|
#define OP_PACKET_PARAMS_8X 0x8C // crc, preamble, payload length, etc.
|
|
#define OP_STATUS_8X 0xC0
|
|
#define OP_TX_PARAMS_8X 0x8E // set dbm, etc
|
|
#define OP_PACKET_TYPE_8X 0x8A
|
|
#define OP_BUFFER_BASE_ADDR_8X 0x8F
|
|
#define OP_READ_REGISTER_8X 0x19
|
|
#define OP_WRITE_REGISTER_8X 0x18
|
|
#define IRQ_TX_DONE_MASK_8X 0x01
|
|
#define IRQ_RX_DONE_MASK_8X 0x02
|
|
#define IRQ_HEADER_DET_MASK_8X 0x10
|
|
#define IRQ_HEADER_ERROR_MASK_8X 0x20
|
|
#define IRQ_PAYLOAD_CRC_ERROR_MASK_8X 0x40
|
|
|
|
#define MODE_LONG_RANGE_MODE_8X 0x01
|
|
|
|
#define OP_FIFO_WRITE_8X 0x1A
|
|
#define OP_FIFO_READ_8X 0x1B
|
|
#define IRQ_PREAMBLE_DET_MASK_8X 0x80
|
|
|
|
#define REG_PACKET_SIZE 0x901
|
|
#define REG_FIRM_VER_MSB 0x154
|
|
#define REG_FIRM_VER_LSB 0x153
|
|
|
|
#define XTAL_FREQ_8X (double)52000000
|
|
#define FREQ_DIV_8X (double)pow(2.0, 18.0)
|
|
#define FREQ_STEP_8X (double)(XTAL_FREQ_8X / FREQ_DIV_8X)
|
|
|
|
#if defined(NRF52840_XXAA)
|
|
extern SPIClass spiModem;
|
|
#define SPI spiModem
|
|
#endif
|
|
|
|
extern SPIClass SPI;
|
|
|
|
#define MAX_PKT_LENGTH 255
|
|
|
|
sx128x::sx128x() :
|
|
_spiSettings(8E6, MSBFIRST, SPI_MODE0),
|
|
_ss(LORA_DEFAULT_SS_PIN), _reset(LORA_DEFAULT_RESET_PIN), _dio0(LORA_DEFAULT_DIO0_PIN), _rxen(LORA_DEFAULT_RXEN_PIN), _busy(LORA_DEFAULT_BUSY_PIN),
|
|
_frequency(0),
|
|
_txp(0),
|
|
_sf(0x50),
|
|
_bw(0x34),
|
|
_cr(0x01),
|
|
_packetIndex(0),
|
|
_preambleLength(18),
|
|
_implicitHeaderMode(0),
|
|
_payloadLength(255),
|
|
_crcMode(0),
|
|
_fifo_tx_addr_ptr(0),
|
|
_fifo_rx_addr_ptr(0),
|
|
_packet({0}),
|
|
_rxPacketLength(0),
|
|
_preinit_done(false),
|
|
_onReceive(NULL)
|
|
{
|
|
// overide Stream timeout value
|
|
setTimeout(0);
|
|
}
|
|
|
|
bool sx128x::preInit() {
|
|
// setup pins
|
|
pinMode(_ss, OUTPUT);
|
|
// set SS high
|
|
digitalWrite(_ss, HIGH);
|
|
|
|
SPI.begin();
|
|
|
|
// check version (retry for up to 2 seconds)
|
|
long start = millis();
|
|
|
|
uint8_t version_msb;
|
|
uint8_t version_lsb;
|
|
|
|
while (((millis() - start) < 2000) && (millis() >= start)) {
|
|
|
|
version_msb = readRegister(REG_FIRM_VER_MSB);
|
|
version_lsb = readRegister(REG_FIRM_VER_LSB);
|
|
|
|
if ((version_msb == 0xB7 && version_lsb == 0xA9) || (version_msb == 0xB5 && version_lsb == 0xA9)) {
|
|
break;
|
|
}
|
|
delay(100);
|
|
}
|
|
if ((version_msb != 0xB7 || version_lsb != 0xA9) && (version_msb != 0xB5 || version_lsb != 0xA9)) {
|
|
return false;
|
|
}
|
|
|
|
_preinit_done = true;
|
|
return true;
|
|
}
|
|
|
|
uint8_t ISR_VECT sx128x::readRegister(uint16_t address)
|
|
{
|
|
return singleTransfer(OP_READ_REGISTER_8X, address, 0x00);
|
|
}
|
|
|
|
void sx128x::writeRegister(uint16_t address, uint8_t value)
|
|
{
|
|
singleTransfer(OP_WRITE_REGISTER_8X, address, value);
|
|
}
|
|
|
|
uint8_t ISR_VECT sx128x::singleTransfer(uint8_t opcode, uint16_t address, uint8_t value)
|
|
{
|
|
waitOnBusy();
|
|
|
|
uint8_t response;
|
|
|
|
digitalWrite(_ss, LOW);
|
|
|
|
SPI.beginTransaction(_spiSettings);
|
|
SPI.transfer(opcode);
|
|
SPI.transfer((address & 0xFF00) >> 8);
|
|
SPI.transfer(address & 0x00FF);
|
|
if (opcode == OP_READ_REGISTER_8X) {
|
|
SPI.transfer(0x00);
|
|
}
|
|
response = SPI.transfer(value);
|
|
SPI.endTransaction();
|
|
|
|
digitalWrite(_ss, HIGH);
|
|
|
|
return response;
|
|
}
|
|
|
|
void sx128x::rxAntEnable()
|
|
{
|
|
if (_txen != -1) {
|
|
digitalWrite(_txen, LOW);
|
|
}
|
|
if (_rxen != -1) {
|
|
digitalWrite(_rxen, HIGH);
|
|
}
|
|
}
|
|
|
|
void sx128x::txAntEnable()
|
|
{
|
|
if (_txen != -1) {
|
|
digitalWrite(_txen, HIGH);
|
|
}
|
|
if (_rxen != -1) {
|
|
digitalWrite(_rxen, LOW);
|
|
}
|
|
}
|
|
|
|
void sx128x::loraMode() {
|
|
// enable lora mode on the SX1262 chip
|
|
uint8_t mode = MODE_LONG_RANGE_MODE_8X;
|
|
executeOpcode(OP_PACKET_TYPE_8X, &mode, 1);
|
|
}
|
|
|
|
void sx128x::waitOnBusy() {
|
|
unsigned long time = millis();
|
|
if (_busy != -1) {
|
|
while (digitalRead(_busy) == HIGH)
|
|
{
|
|
if (millis() >= (time + 100)) {
|
|
break;
|
|
}
|
|
// do nothing
|
|
}
|
|
}
|
|
}
|
|
|
|
void sx128x::executeOpcode(uint8_t opcode, uint8_t *buffer, uint8_t size)
|
|
{
|
|
waitOnBusy();
|
|
|
|
digitalWrite(_ss, LOW);
|
|
|
|
SPI.beginTransaction(_spiSettings);
|
|
SPI.transfer(opcode);
|
|
|
|
for (int i = 0; i < size; i++)
|
|
{
|
|
SPI.transfer(buffer[i]);
|
|
}
|
|
|
|
SPI.endTransaction();
|
|
|
|
digitalWrite(_ss, HIGH);
|
|
}
|
|
|
|
void sx128x::executeOpcodeRead(uint8_t opcode, uint8_t *buffer, uint8_t size)
|
|
{
|
|
waitOnBusy();
|
|
|
|
digitalWrite(_ss, LOW);
|
|
|
|
SPI.beginTransaction(_spiSettings);
|
|
SPI.transfer(opcode);
|
|
SPI.transfer(0x00);
|
|
|
|
for (int i = 0; i < size; i++)
|
|
{
|
|
buffer[i] = SPI.transfer(0x00);
|
|
}
|
|
|
|
SPI.endTransaction();
|
|
|
|
digitalWrite(_ss, HIGH);
|
|
}
|
|
|
|
void sx128x::writeBuffer(const uint8_t* buffer, size_t size)
|
|
{
|
|
waitOnBusy();
|
|
|
|
digitalWrite(_ss, LOW);
|
|
|
|
SPI.beginTransaction(_spiSettings);
|
|
SPI.transfer(OP_FIFO_WRITE_8X);
|
|
SPI.transfer(_fifo_tx_addr_ptr);
|
|
|
|
for (int i = 0; i < size; i++)
|
|
{
|
|
SPI.transfer(buffer[i]);
|
|
_fifo_tx_addr_ptr++;
|
|
}
|
|
|
|
SPI.endTransaction();
|
|
|
|
digitalWrite(_ss, HIGH);
|
|
}
|
|
|
|
void sx128x::readBuffer(uint8_t* buffer, size_t size)
|
|
{
|
|
waitOnBusy();
|
|
|
|
digitalWrite(_ss, LOW);
|
|
|
|
SPI.beginTransaction(_spiSettings);
|
|
SPI.transfer(OP_FIFO_READ_8X);
|
|
SPI.transfer(_fifo_rx_addr_ptr);
|
|
SPI.transfer(0x00);
|
|
|
|
for (int i = 0; i < size; i++)
|
|
{
|
|
buffer[i] = SPI.transfer(0x00);
|
|
}
|
|
|
|
SPI.endTransaction();
|
|
|
|
digitalWrite(_ss, HIGH);
|
|
}
|
|
|
|
void sx128x::setModulationParams(uint8_t sf, uint8_t bw, uint8_t cr) {
|
|
// because there is no access to these registers on the sx1280, we have
|
|
// to set all these parameters at once or not at all.
|
|
uint8_t buf[3];
|
|
|
|
buf[0] = sf;
|
|
buf[1] = bw;
|
|
buf[2] = cr;
|
|
executeOpcode(OP_MODULATION_PARAMS_8X, buf, 3);
|
|
|
|
if (sf <= 6) {
|
|
writeRegister(0x925, 0x1E);
|
|
} else if (sf <= 8) {
|
|
writeRegister(0x925, 0x37);
|
|
} else if (sf >= 9) {
|
|
writeRegister(0x925, 0x32);
|
|
}
|
|
writeRegister(0x093C, 0x1);
|
|
}
|
|
|
|
void sx128x::setPacketParams(uint32_t preamble, uint8_t headermode, uint8_t length, uint8_t crc) {
|
|
// because there is no access to these registers on the sx1280, we have
|
|
// to set all these parameters at once or not at all.
|
|
uint8_t buf[7];
|
|
|
|
// calculate exponent and mantissa values for modem
|
|
uint8_t e = 1;
|
|
uint8_t m = 1;
|
|
uint32_t preamblelen;
|
|
|
|
for (e <= 15; e++;) {
|
|
for (m <= 15; m++;) {
|
|
preamblelen = m * (uint32_t(1) << e);
|
|
if (preamblelen >= preamble) break;
|
|
}
|
|
if (preamblelen >= preamble) break;
|
|
}
|
|
|
|
buf[0] = (e << 4) | m;
|
|
buf[1] = headermode;
|
|
buf[2] = length;
|
|
buf[3] = crc;
|
|
// standard IQ setting (no inversion)
|
|
buf[4] = 0x40;
|
|
// unused params
|
|
buf[5] = 0x00;
|
|
buf[6] = 0x00;
|
|
|
|
executeOpcode(OP_PACKET_PARAMS_8X, buf, 7);
|
|
}
|
|
|
|
int sx128x::begin(unsigned long frequency)
|
|
{
|
|
if (_reset != -1) {
|
|
pinMode(_reset, OUTPUT);
|
|
|
|
// perform reset
|
|
digitalWrite(_reset, LOW);
|
|
delay(10);
|
|
digitalWrite(_reset, HIGH);
|
|
delay(10);
|
|
}
|
|
|
|
if (_busy != -1) {
|
|
pinMode(_busy, INPUT);
|
|
}
|
|
|
|
if (!_preinit_done) {
|
|
if (!preInit()) {
|
|
return false;
|
|
}
|
|
}
|
|
|
|
idle();
|
|
loraMode();
|
|
rxAntEnable();
|
|
|
|
setFrequency(frequency);
|
|
|
|
// set LNA boost
|
|
// todo: implement this
|
|
//writeRegister(REG_LNA, 0x96);
|
|
|
|
setModulationParams(_sf, _bw, _cr);
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
|
|
// set output power to 2 dBm
|
|
setTxPower(2);
|
|
|
|
// set base addresses
|
|
uint8_t basebuf[2] = {0};
|
|
executeOpcode(OP_BUFFER_BASE_ADDR_8X, basebuf, 2);
|
|
|
|
return 1;
|
|
}
|
|
|
|
void sx128x::end()
|
|
{
|
|
// put in sleep mode
|
|
sleep();
|
|
|
|
// stop SPI
|
|
SPI.end();
|
|
|
|
_preinit_done = false;
|
|
}
|
|
|
|
int sx128x::beginPacket(int implicitHeader)
|
|
{
|
|
// put in standby mode
|
|
idle();
|
|
|
|
if (implicitHeader) {
|
|
implicitHeaderMode();
|
|
} else {
|
|
explicitHeaderMode();
|
|
}
|
|
|
|
_payloadLength = 0;
|
|
_fifo_tx_addr_ptr = 0;
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
|
|
return 1;
|
|
}
|
|
|
|
int sx128x::endPacket()
|
|
{
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
|
|
txAntEnable();
|
|
|
|
// put in single TX mode
|
|
uint8_t timeout[3] = {0};
|
|
executeOpcode(OP_TX_8X, timeout, 3);
|
|
|
|
uint8_t buf[2];
|
|
|
|
buf[0] = 0x00;
|
|
buf[1] = 0x00;
|
|
|
|
executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
|
|
|
|
// wait for TX done
|
|
while ((buf[1] & IRQ_TX_DONE_MASK_8X) == 0) {
|
|
buf[0] = 0x00;
|
|
buf[1] = 0x00;
|
|
executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
|
|
yield();
|
|
}
|
|
|
|
// clear IRQ's
|
|
|
|
uint8_t mask[2];
|
|
mask[0] = 0x00;
|
|
mask[1] = IRQ_TX_DONE_MASK_8X;
|
|
executeOpcode(OP_CLEAR_IRQ_STATUS_8X, mask, 2);
|
|
return 1;
|
|
}
|
|
|
|
uint8_t sx128x::modemStatus() {
|
|
// imitate the register status from the sx1276 / 78
|
|
uint8_t buf[2] = {0};
|
|
|
|
executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
|
|
|
|
uint8_t clearbuf[2] = {0};
|
|
|
|
uint8_t byte = 0x00;
|
|
|
|
if ((buf[0] & IRQ_PREAMBLE_DET_MASK_8X) != 0) {
|
|
byte = byte | 0x01 | 0x04;
|
|
// clear register after reading
|
|
clearbuf[0] = 0xFF;
|
|
}
|
|
|
|
if ((buf[1] & IRQ_HEADER_DET_MASK_8X) != 0) {
|
|
byte = byte | 0x02 | 0x04;
|
|
// clear register after reading
|
|
clearbuf[1] = 0xFF;
|
|
}
|
|
|
|
executeOpcode(OP_CLEAR_IRQ_STATUS_8X, clearbuf, 2);
|
|
|
|
return byte;
|
|
}
|
|
|
|
|
|
uint8_t sx128x::currentRssiRaw() {
|
|
uint8_t byte = 0;
|
|
executeOpcodeRead(OP_CURRENT_RSSI_8X, &byte, 1);
|
|
return byte;
|
|
}
|
|
|
|
int ISR_VECT sx128x::currentRssi() {
|
|
uint8_t byte = 0;
|
|
executeOpcodeRead(OP_CURRENT_RSSI_8X, &byte, 1);
|
|
int rssi = -byte / 2;
|
|
return rssi;
|
|
}
|
|
|
|
uint8_t sx128x::packetRssiRaw() {
|
|
uint8_t buf[5] = {0};
|
|
executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 5);
|
|
return buf[0];
|
|
}
|
|
|
|
int ISR_VECT sx128x::packetRssi() {
|
|
// may need more calculations here
|
|
uint8_t buf[5] = {0};
|
|
executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 5);
|
|
int pkt_rssi = -buf[0] / 2;
|
|
return pkt_rssi;
|
|
}
|
|
|
|
uint8_t ISR_VECT sx128x::packetSnrRaw() {
|
|
uint8_t buf[5] = {0};
|
|
executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 5);
|
|
return buf[1];
|
|
}
|
|
|
|
float ISR_VECT sx128x::packetSnr() {
|
|
uint8_t buf[5] = {0};
|
|
executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 3);
|
|
return float(buf[1]) * 0.25;
|
|
}
|
|
|
|
long sx128x::packetFrequencyError()
|
|
{
|
|
int32_t freqError = 0;
|
|
// todo: implement this, page 120 of sx1280 datasheet
|
|
const float fError = 0.0;
|
|
return static_cast<long>(fError);
|
|
}
|
|
|
|
size_t sx128x::write(uint8_t byte)
|
|
{
|
|
return write(&byte, sizeof(byte));
|
|
}
|
|
|
|
size_t sx128x::write(const uint8_t *buffer, size_t size)
|
|
{
|
|
if ((_payloadLength + size) > MAX_PKT_LENGTH) {
|
|
size = MAX_PKT_LENGTH - _payloadLength;
|
|
}
|
|
|
|
// write data
|
|
writeBuffer(buffer, size);
|
|
_payloadLength = _payloadLength + size;
|
|
return size;
|
|
}
|
|
|
|
int ISR_VECT sx128x::available()
|
|
{
|
|
return _rxPacketLength - _packetIndex;
|
|
}
|
|
|
|
int ISR_VECT sx128x::read()
|
|
{
|
|
if (!available()) {
|
|
return -1;
|
|
}
|
|
|
|
uint8_t byte = _packet[_packetIndex];
|
|
_packetIndex++;
|
|
return byte;
|
|
}
|
|
|
|
int sx128x::peek()
|
|
{
|
|
if (!available()) {
|
|
return -1;
|
|
}
|
|
|
|
uint8_t b = _packet[_packetIndex];
|
|
return b;
|
|
}
|
|
|
|
void sx128x::flush()
|
|
{
|
|
}
|
|
|
|
void sx128x::onReceive(void(*callback)(int))
|
|
{
|
|
_onReceive = callback;
|
|
|
|
if (callback) {
|
|
pinMode(_dio0, INPUT);
|
|
|
|
// set preamble and header detection irqs, plus dio0 mask
|
|
uint8_t buf[8];
|
|
|
|
// set irq masks, enable all
|
|
buf[0] = 0xFF;
|
|
buf[1] = 0xFF;
|
|
|
|
// set dio0 masks
|
|
buf[2] = 0x00;
|
|
buf[3] = IRQ_RX_DONE_MASK_8X;
|
|
|
|
// set dio1 masks
|
|
buf[4] = 0x00;
|
|
buf[5] = 0x00;
|
|
|
|
// set dio2 masks
|
|
buf[6] = 0x00;
|
|
buf[7] = 0x00;
|
|
|
|
executeOpcode(OP_SET_IRQ_FLAGS_8X, buf, 8);
|
|
//#ifdef SPI_HAS_NOTUSINGINTERRUPT
|
|
// SPI.usingInterrupt(digitalPinToInterrupt(_dio0));
|
|
//#endif
|
|
attachInterrupt(digitalPinToInterrupt(_dio0), sx128x::onDio0Rise, RISING);
|
|
} else {
|
|
detachInterrupt(digitalPinToInterrupt(_dio0));
|
|
//#ifdef SPI_HAS_NOTUSINGINTERRUPT
|
|
// SPI.notUsingInterrupt(digitalPinToInterrupt(_dio0));
|
|
//#endif
|
|
}
|
|
}
|
|
|
|
void sx128x::receive(int size)
|
|
{
|
|
if (size > 0) {
|
|
implicitHeaderMode();
|
|
|
|
// tell radio payload length
|
|
_rxPacketLength = size;
|
|
//_payloadLength = size;
|
|
//setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
} else {
|
|
explicitHeaderMode();
|
|
}
|
|
|
|
rxAntEnable();
|
|
|
|
uint8_t mode[3] = {0xFF, 0xFF, 0xFF}; // continuous mode
|
|
executeOpcode(OP_RX_8X, mode, 3);
|
|
}
|
|
|
|
void sx128x::idle()
|
|
{
|
|
#if HAS_TCXO
|
|
// STDBY_XOSC
|
|
uint8_t byte = 0x01;
|
|
#else
|
|
// STDBY_RC
|
|
uint8_t byte = 0x00;
|
|
#endif
|
|
executeOpcode(OP_STANDBY_8X, &byte, 1);
|
|
}
|
|
|
|
void sx128x::sleep()
|
|
{
|
|
uint8_t byte = 0x00;
|
|
executeOpcode(OP_SLEEP_8X, &byte, 1);
|
|
}
|
|
|
|
void sx128x::enableTCXO() {
|
|
// todo: need to check how to implement on sx1280
|
|
}
|
|
|
|
void sx128x::disableTCXO() {
|
|
// todo: need to check how to implement on sx1280
|
|
}
|
|
|
|
void sx128x::setTxPower(int level, int outputPin) {
|
|
if (level > 13) {
|
|
level = 13;
|
|
} else if (level < -18) {
|
|
level = -18;
|
|
}
|
|
|
|
_txp = level;
|
|
|
|
level = level + 18;
|
|
|
|
uint8_t tx_buf[2];
|
|
|
|
tx_buf[0] = level;
|
|
tx_buf[1] = 0xE0; // ramping time - 20 microseconds
|
|
|
|
executeOpcode(OP_TX_PARAMS_8X, tx_buf, 2);
|
|
}
|
|
|
|
uint8_t sx128x::getTxPower() {
|
|
return _txp;
|
|
}
|
|
|
|
void sx128x::setFrequency(unsigned long frequency) {
|
|
_frequency = frequency;
|
|
|
|
uint8_t buf[3];
|
|
|
|
uint32_t freq = (uint32_t)((double)frequency / (double)FREQ_STEP_8X);
|
|
|
|
buf[0] = ((freq >> 16) & 0xFF);
|
|
buf[1] = ((freq >> 8) & 0xFF);
|
|
buf[2] = (freq & 0xFF);
|
|
|
|
executeOpcode(OP_RF_FREQ_8X, buf, 3);
|
|
}
|
|
|
|
uint32_t sx128x::getFrequency() {
|
|
// we can't read the frequency on the sx1280
|
|
uint32_t frequency = _frequency;
|
|
|
|
return frequency;
|
|
}
|
|
|
|
void sx128x::setSpreadingFactor(int sf)
|
|
{
|
|
if (sf < 5) {
|
|
sf = 5;
|
|
} else if (sf > 12) {
|
|
sf = 12;
|
|
}
|
|
|
|
_sf = sf << 4;
|
|
|
|
setModulationParams(sf << 4, _bw, _cr);
|
|
handleLowDataRate();
|
|
}
|
|
|
|
long sx128x::getSignalBandwidth()
|
|
{
|
|
int bw = _bw;
|
|
switch (bw) {
|
|
case 0x34: return 203.125E3;
|
|
case 0x26: return 406.25E3;
|
|
case 0x18: return 812.5E3;
|
|
case 0x0A: return 1625E3;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void sx128x::handleLowDataRate(){
|
|
// todo: do i need this??
|
|
}
|
|
|
|
void sx128x::optimizeModemSensitivity(){
|
|
// todo: check if there's anything the sx1280 can do here
|
|
}
|
|
|
|
void sx128x::setSignalBandwidth(long sbw)
|
|
{
|
|
if (sbw <= 203.125E3) {
|
|
_bw = 0x34;
|
|
} else if (sbw <= 406.25E3) {
|
|
_bw = 0x26;
|
|
} else if (sbw <= 812.5E3) {
|
|
_bw = 0x18;
|
|
} else {
|
|
_bw = 0x0A;
|
|
}
|
|
|
|
setModulationParams(_sf, _bw, _cr);
|
|
|
|
handleLowDataRate();
|
|
optimizeModemSensitivity();
|
|
}
|
|
|
|
void sx128x::setCodingRate4(int denominator)
|
|
{
|
|
if (denominator < 5) {
|
|
denominator = 5;
|
|
} else if (denominator > 8) {
|
|
denominator = 8;
|
|
}
|
|
|
|
_cr = denominator - 4;
|
|
|
|
// todo: add support for new interleaving scheme, see page 117 of sx1280
|
|
// datasheet
|
|
|
|
// update cr values for sx1280's use
|
|
|
|
setModulationParams(_sf, _bw, _cr);
|
|
}
|
|
|
|
void sx128x::setPreambleLength(long length)
|
|
{
|
|
_preambleLength = length;
|
|
setPacketParams(length, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
}
|
|
|
|
void sx128x::setSyncWord(int sw)
|
|
{
|
|
// not implemented
|
|
}
|
|
|
|
void sx128x::enableCrc()
|
|
{
|
|
_crcMode = 0x20;
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
}
|
|
|
|
void sx128x::disableCrc()
|
|
{
|
|
_crcMode = 0;
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
}
|
|
|
|
byte sx128x::random()
|
|
{
|
|
// todo: implement
|
|
}
|
|
|
|
void sx128x::setPins(int ss, int reset, int dio0, int busy, int rxen, int txen)
|
|
{
|
|
_ss = ss;
|
|
_reset = reset;
|
|
_dio0 = dio0;
|
|
_busy = busy;
|
|
_rxen = rxen;
|
|
_txen = txen;
|
|
}
|
|
|
|
void sx128x::setSPIFrequency(uint32_t frequency)
|
|
{
|
|
_spiSettings = SPISettings(frequency, MSBFIRST, SPI_MODE0);
|
|
}
|
|
|
|
void sx128x::dumpRegisters(Stream& out)
|
|
{
|
|
for (int i = 0; i < 128; i++) {
|
|
out.print("0x");
|
|
out.print(i, HEX);
|
|
out.print(": 0x");
|
|
out.println(readRegister(i), HEX);
|
|
}
|
|
}
|
|
|
|
void sx128x::explicitHeaderMode()
|
|
{
|
|
_implicitHeaderMode = 0;
|
|
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
}
|
|
|
|
void sx128x::implicitHeaderMode()
|
|
{
|
|
_implicitHeaderMode = 0x80;
|
|
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
|
|
}
|
|
|
|
|
|
void ISR_VECT sx128x::handleDio0Rise()
|
|
{
|
|
uint8_t buf[2];
|
|
|
|
buf[0] = 0x00;
|
|
buf[1] = 0x00;
|
|
|
|
executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
|
|
|
|
executeOpcode(OP_CLEAR_IRQ_STATUS_8X, buf, 2);
|
|
|
|
if ((buf[1] & IRQ_PAYLOAD_CRC_ERROR_MASK_8X) == 0) {
|
|
// received a packet
|
|
_packetIndex = 0;
|
|
|
|
uint8_t rxbuf[2] = {0};
|
|
executeOpcodeRead(OP_RX_BUFFER_STATUS_8X, rxbuf, 2);
|
|
_rxPacketLength = rxbuf[0];
|
|
_fifo_rx_addr_ptr = rxbuf[1];
|
|
readBuffer(_packet, _rxPacketLength);
|
|
|
|
if (_onReceive) {
|
|
_onReceive(_rxPacketLength);
|
|
}
|
|
|
|
}
|
|
}
|
|
|
|
void ISR_VECT sx128x::onDio0Rise()
|
|
{
|
|
sx128x_modem.handleDio0Rise();
|
|
}
|
|
|
|
sx128x sx128x_modem;
|