mirror of
https://github.com/liberatedsystems/RNode_Firmware_CE.git
synced 2024-12-26 07:59:23 -05:00
Merge pull request #17 from nathmo/patch-1
Added a few info in CONTRIBUTING.md
This commit is contained in:
jacobeva
GitHub
commit
f778e4d76f
@ -1,7 +1,8 @@
|
||||
# Board support
|
||||
If you wish to add support for a specific board to the project, all you have to do (if it's ESP32 or nRF52), is write an additional entry for `Boards.h`.
|
||||
If you wish to add support for a specific board to the project, all you have to do (if it's ESP32 or nRF52), is write an additional entry for `Boards.h` and `Utilities.h` and the `Makefile` .
|
||||
|
||||
This entry should include, at a minimum, the following:
|
||||
### Boards.h
|
||||
This entry in `Boards.h` should include, at a minimum, the following:
|
||||
* whether the device has bluetooth / BLE
|
||||
* whether the device has a PMU
|
||||
* whether the device has an EEPROM (false in all cases for nRF52, true for ESP32)
|
||||
@ -10,7 +11,47 @@ This entry should include, at a minimum, the following:
|
||||
* whether the modem has a busy pin
|
||||
* RX and TX leds (preferably LEDs of different colours)
|
||||
|
||||
# Check this area...
|
||||
here is an example :
|
||||
the new entry to add whoses number should not be used aldready
|
||||
```
|
||||
#define BOARD_GENERIC_ESP32_C3 0x3B
|
||||
```
|
||||
and the board definition
|
||||
```
|
||||
#elif BOARD_MODEL == BOARD_GENERIC_ESP32_C3
|
||||
#define HAS_BLUETOOTH false
|
||||
#define HAS_CONSOLE true
|
||||
#define HAS_EEPROM true
|
||||
#define INTERFACE_COUNT 1
|
||||
const int pin_led_rx = 9;
|
||||
const int pin_led_tx = 8;
|
||||
const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
|
||||
const bool interface_cfg[INTERFACE_COUNT][3] = {
|
||||
// SX127X
|
||||
{
|
||||
true, // DEFAULT_SPI
|
||||
false, // HAS_TCXO
|
||||
false // DIO2_AS_RF_SWITCH
|
||||
},
|
||||
};
|
||||
const int8_t interface_pins[INTERFACE_COUNT][10] = {
|
||||
// SX127X
|
||||
{
|
||||
7, // pin_ss
|
||||
4, // pin_sclk
|
||||
6, // pin_mosi
|
||||
5, // pin_miso
|
||||
-1, // pin_busy
|
||||
2, // pin_dio
|
||||
3, // pin_reset
|
||||
-1, // pin_txen
|
||||
-1, // pin_rxen
|
||||
-1 // pin_tcxo_enable
|
||||
}
|
||||
};
|
||||
|
||||
```
|
||||
|
||||
see https://github.com/espressif/arduino-esp32/blob/master/cores/esp32/esp32-hal-spi.h#L39
|
||||
Effectively, there are multiple SPI buses we can map to pins on these
|
||||
devices (including the hardware SPI bus)
|
||||
@ -98,6 +139,56 @@ An example of an entry using the SX1280 modem can be seen below:
|
||||
const int pin_led_tx = 6;
|
||||
```
|
||||
|
||||
|
||||
### Utilities.h
|
||||
you should add something like this to drive the led :
|
||||
|
||||
```
|
||||
#elif BOARD_MODEL == BOARD_GENERIC_ESP32_C3
|
||||
void led_rx_on() { digitalWrite(pin_led_rx, HIGH); }
|
||||
void led_rx_off() { digitalWrite(pin_led_rx, LOW); }
|
||||
void led_tx_on() { digitalWrite(pin_led_tx, HIGH); }
|
||||
void led_tx_off() { digitalWrite(pin_led_tx, LOW); }
|
||||
```
|
||||
|
||||
### Makefile
|
||||
|
||||
one entry to build the firmware
|
||||
```
|
||||
firmware-genericesp32c3:
|
||||
arduino-cli compile --fqbn esp32:esp32:esp32c3:CDCOnBoot=cdc -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x3B\""
|
||||
```
|
||||
pay attention the the DBOARD_MODEL= value as you must choose an unsigned one for your board.
|
||||
|
||||
one entry to upload the firmware to the board
|
||||
|
||||
```
|
||||
upload-genericesp32c3:
|
||||
arduino-cli upload -p /dev/ttyACM0 --fqbn esp32:esp32:esp32c3
|
||||
@sleep 1
|
||||
rnodeconf /dev/ttyACM0 --firmware-hash $$(./partition_hashes ./build/esp32.esp32.esp32c3/RNode_Firmware_CE.ino.bin)
|
||||
@sleep 3
|
||||
python ./Release/esptool/esptool.py --chip esp32c3 --port /dev/ttyACM0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
|
||||
```
|
||||
|
||||
and finally one entry to make a realease for the firmware
|
||||
|
||||
```
|
||||
release-genericesp32c3:
|
||||
arduino-cli compile --fqbn esp32:esp32:esp32c3:CDCOnBoot=cdc -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x3B\""
|
||||
cp ~/.arduino15/packages/esp32/hardware/esp32/$(ESP_IDF_VER)/tools/partitions/boot_app0.bin build/rnode_firmware_esp32_generic-c3.boot_app0
|
||||
cp build/esp32.esp32.esp32c3/RNode_Firmware_CE.ino.bin build/rnode_firmware_esp32c3_generic.bin
|
||||
cp build/esp32.esp32.esp32c3/RNode_Firmware_CE.ino.bootloader.bin build/rnode_firmware_esp32c3_generic.bootloader
|
||||
cp build/esp32.esp32.esp32c3/RNode_Firmware_CE.ino.partitions.bin build/rnode_firmware_esp32c3_generic.partitions
|
||||
zip --junk-paths ./Release/rnode_firmware_esp32c3_generic.zip ./Release/esptool/esptool.py ./Release/console_image.bin build/rnode_firmware_esp32c3_generic.boot_app0 build/rnode_firmware_esp32c3_generic.bin build/rnode_firmware_esp32c3_generic.bootloader build/rnode_firmware_esp32c3_generic.partitions
|
||||
rm -r build
|
||||
```
|
||||
dont forget to add this entry to the `release-all` action.
|
||||
|
||||
```
|
||||
release-all: console-site spiffs-image release-tbeam release-tbeam_sx1262 release-lora32_v10 release-lora32_v20 release-lora32_v21 release-lora32_v10_extled release-lora32_v20_extled release-lora32_v21_extled release-lora32_v21_tcxo release-featheresp32 release-genericesp32 release-genericesp32c3 release-heltec32_v2 release-heltec32_v3 release-heltec32_v2_extled release-rnode_ng_20 release-rnode_ng_21 release-t3s3 release-hashe
|
||||
```
|
||||
|
||||
Please submit this, and any other support in different areas of the project your board may require, as a PR for my consideration.
|
||||
|
||||
# Feature request
|
||||
|
||||
Loading…
Reference in New Issue
Block a user