mirror of
https://github.com/liberatedsystems/RNode_Firmware_CE.git
synced 2024-12-30 09:56:14 -05:00
Added register values and op-codes. Cleanup.
This commit is contained in:
parent
fe50c2cac9
commit
cec979997e
105
sx126x.cpp
105
sx126x.cpp
@ -43,12 +43,20 @@
|
||||
#define OP_WRITE_REGISTER_6X 0x0D
|
||||
#define OP_DIO3_TCXO_CTRL_6X 0x97
|
||||
#define OP_DIO2_RF_CTRL_6X 0x9D
|
||||
#define OP_CAD_PARAMS 0x88
|
||||
#define OP_CALIBRATE_6X 0x89
|
||||
#define OP_RX_TX_FALLBACK_MODE_6X 0x93
|
||||
#define OP_REGULATOR_MODE_6X 0x96
|
||||
#define OP_CALIBRATE_IMAGE_6X 0x98
|
||||
|
||||
#define MASK_CALIBRATE_ALL 0x7f
|
||||
|
||||
#define IRQ_TX_DONE_MASK_6X 0x01
|
||||
#define IRQ_RX_DONE_MASK_6X 0x02
|
||||
#define IRQ_HEADER_DET_MASK_6X 0x10
|
||||
#define IRQ_PREAMBLE_DET_MASK_6X 0x04
|
||||
#define IRQ_PAYLOAD_CRC_ERROR_MASK_6X 0x40
|
||||
#define IRQ_ALL_MASK_6X 0b0100001111111111
|
||||
|
||||
#define MODE_LONG_RANGE_MODE_6X 0x01
|
||||
|
||||
@ -70,6 +78,12 @@
|
||||
#define MODE_TCXO_1_7V_6X 0x01
|
||||
#define MODE_TCXO_1_6V_6X 0x00
|
||||
|
||||
#define MODE_STDBY_RC_6X 0x00
|
||||
#define MODE_STDBY_XOSC_6X 0x01
|
||||
#define MODE_FALLBACK_STDBY_RC_6X 0x20
|
||||
#define MODE_IMPLICIT_HEADER 0x01
|
||||
#define MODE_EXPLICIT_HEADER 0x00
|
||||
|
||||
#define SYNC_WORD_6X 0x1424
|
||||
|
||||
#define XTAL_FREQ_6X (double)32000000
|
||||
@ -331,6 +345,46 @@ void sx126x::reset(void) {
|
||||
}
|
||||
}
|
||||
|
||||
void sx126x::calibrate(void) {
|
||||
// Put in STDBY_RC mode before calibration
|
||||
uint8_t mode_byte = MODE_STDBY_RC_6X;
|
||||
executeOpcode(OP_STANDBY_6X, &mode_byte, 1);
|
||||
|
||||
// calibrate RC64k, RC13M, PLL, ADC and image
|
||||
uint8_t calibrate = MASK_CALIBRATE_ALL;
|
||||
executeOpcode(OP_CALIBRATE_6X, &calibrate, 1);
|
||||
|
||||
delay(5);
|
||||
waitOnBusy();
|
||||
}
|
||||
|
||||
void sx126x::calibrate_image(long frequency) {
|
||||
uint8_t image_freq[2] = {0};
|
||||
|
||||
if (frequency >= 430E6 && frequency <= 440E6) {
|
||||
image_freq[0] = 0x6B;
|
||||
image_freq[1] = 0x6F;
|
||||
}
|
||||
else if (frequency >= 470E6 && frequency <= 510E6) {
|
||||
image_freq[0] = 0x75;
|
||||
image_freq[1] = 0x81;
|
||||
}
|
||||
else if (frequency >= 779E6 && frequency <= 787E6) {
|
||||
image_freq[0] = 0xC1;
|
||||
image_freq[1] = 0xC5;
|
||||
}
|
||||
else if (frequency >= 863E6 && frequency <= 870E6) {
|
||||
image_freq[0] = 0xD7;
|
||||
image_freq[1] = 0xDB;
|
||||
}
|
||||
else if (frequency >= 902E6 && frequency <= 928E6) {
|
||||
image_freq[0] = 0xE1;
|
||||
image_freq[1] = 0xE9;
|
||||
}
|
||||
|
||||
executeOpcode(OP_CALIBRATE_IMAGE_6X, image_freq, 2);
|
||||
waitOnBusy();
|
||||
}
|
||||
|
||||
int sx126x::begin(long frequency)
|
||||
{
|
||||
@ -350,20 +404,13 @@ int sx126x::begin(long frequency)
|
||||
pinMode(_rxen, OUTPUT);
|
||||
}
|
||||
|
||||
// Put in STDBY_RC mode before calibration
|
||||
uint8_t mode_byte = 0x00;
|
||||
executeOpcode(OP_STANDBY_6X, &mode_byte, 1);
|
||||
calibrate();
|
||||
calibrate_image(frequency);
|
||||
|
||||
// calibrate RC64k, RC13M, PLL, ADC and image
|
||||
uint8_t calibrate = 0x7F;
|
||||
executeOpcode(OP_CALIBRATE_6X, &calibrate, 1);
|
||||
|
||||
#if HAS_TCXO
|
||||
enableTCXO();
|
||||
#endif
|
||||
enableTCXO();
|
||||
|
||||
loraMode();
|
||||
idle();
|
||||
standby();
|
||||
|
||||
// Set sync word
|
||||
setSyncWord(SYNC_WORD_6X);
|
||||
@ -408,8 +455,7 @@ void sx126x::end()
|
||||
|
||||
int sx126x::beginPacket(int implicitHeader)
|
||||
{
|
||||
// put in standby mode
|
||||
idle();
|
||||
standby();
|
||||
|
||||
if (implicitHeader) {
|
||||
implicitHeaderMode();
|
||||
@ -654,12 +700,12 @@ void sx126x::receive(int size)
|
||||
executeOpcode(OP_RX_6X, mode, 3);
|
||||
}
|
||||
|
||||
void sx126x::idle()
|
||||
void sx126x::standby()
|
||||
{
|
||||
// STDBY_XOSC
|
||||
uint8_t byte = 0x01;
|
||||
uint8_t byte = MODE_STDBY_XOSC_6X;
|
||||
// STDBY_RC
|
||||
// uint8_t byte = 0x00;
|
||||
// uint8_t byte = MODE_STDBY_RC_6X;
|
||||
executeOpcode(OP_STANDBY_6X, &byte, 1);
|
||||
}
|
||||
|
||||
@ -670,19 +716,18 @@ void sx126x::sleep()
|
||||
}
|
||||
|
||||
void sx126x::enableTCXO() {
|
||||
// only tested for RAK4630, voltage may be different on other platforms
|
||||
#if HAS_TCXO
|
||||
#if BOARD_MODEL == BOARD_RAK4630
|
||||
uint8_t buf[4] = {MODE_TCXO_3_3V_6X, 0x00, 0x00, 0xFF};
|
||||
#elif BOARD_MODEL == BOARD_TBEAM
|
||||
uint8_t buf[4] = {MODE_TCXO_1_8V_6X, 0x00, 0x00, 0xFF};
|
||||
#endif
|
||||
|
||||
executeOpcode(OP_DIO3_TCXO_CTRL_6X, buf, 4);
|
||||
#endif
|
||||
}
|
||||
|
||||
void sx126x::disableTCXO() {
|
||||
// currently cannot disable on SX1262?
|
||||
}
|
||||
// TODO: Once enabled, SX1262 needs a complete reset to disable TCXO
|
||||
void sx126x::disableTCXO() { }
|
||||
|
||||
void sx126x::setTxPower(int level, int outputPin) {
|
||||
// currently no low power mode for SX1262 implemented, assuming PA boost
|
||||
@ -693,26 +738,22 @@ void sx126x::setTxPower(int level, int outputPin) {
|
||||
|
||||
uint8_t pa_buf[4];
|
||||
|
||||
pa_buf[0] = 0x04;
|
||||
pa_buf[1] = 0x07;
|
||||
pa_buf[2] = 0x00;
|
||||
pa_buf[3] = 0x01;
|
||||
pa_buf[0] = 0x04; // PADutyCycle needs to be 0x04 to achieve 22dBm output, but can be lowered for better efficiency at lower outputs
|
||||
pa_buf[1] = 0x07; // HPMax at 0x07 is maximum supported for SX1262
|
||||
pa_buf[2] = 0x00; // DeviceSel 0x00 for SX1262 (0x01 for SX1261)
|
||||
pa_buf[3] = 0x01; // PALut always 0x01 (reserved according to datasheet)
|
||||
|
||||
executeOpcode(OP_PA_CONFIG_6X, pa_buf, 4); // set pa_config for high power
|
||||
|
||||
if (level > 22) {
|
||||
level = 22;
|
||||
}
|
||||
else if (level < -9) {
|
||||
level = -9;
|
||||
}
|
||||
if (level > 22) { level = 22; }
|
||||
else if (level < -9) { level = -9; }
|
||||
|
||||
writeRegister(REG_OCP_6X, 0x38); // 160mA limit, overcurrent protection
|
||||
|
||||
uint8_t tx_buf[2];
|
||||
|
||||
tx_buf[0] = level;
|
||||
tx_buf[1] = 0x02; // ramping time - 40 microseconds
|
||||
tx_buf[1] = 0x02; // PA ramping time - 40 microseconds
|
||||
|
||||
executeOpcode(OP_TX_PARAMS_6X, tx_buf, 2);
|
||||
|
||||
|
4
sx126x.h
4
sx126x.h
@ -55,7 +55,7 @@ public:
|
||||
void onReceive(void(*callback)(int));
|
||||
|
||||
void receive(int size = 0);
|
||||
void idle();
|
||||
void standby();
|
||||
void sleep();
|
||||
|
||||
bool preInit();
|
||||
@ -113,6 +113,8 @@ private:
|
||||
void optimizeModemSensitivity();
|
||||
|
||||
void reset(void);
|
||||
void calibrate(void);
|
||||
void calibrate_image(long frequency);
|
||||
|
||||
private:
|
||||
SPISettings _spiSettings;
|
||||
|
@ -90,7 +90,7 @@ void sx127x::setSPIFrequency(uint32_t frequency) { _spiSettings = SPISettings(fr
|
||||
void sx127x::setPins(int ss, int reset, int dio0, int busy) { _ss = ss; _reset = reset; _dio0 = dio0; _busy = busy; }
|
||||
uint8_t ISR_VECT sx127x::readRegister(uint8_t address) { return singleTransfer(address & 0x7f, 0x00); }
|
||||
void sx127x::writeRegister(uint8_t address, uint8_t value) { singleTransfer(address | 0x80, value); }
|
||||
void sx127x::idle() { writeRegister(REG_OP_MODE_7X, MODE_LONG_RANGE_MODE_7X | MODE_STDBY_7X); }
|
||||
void sx127x::standby() { writeRegister(REG_OP_MODE_7X, MODE_LONG_RANGE_MODE_7X | MODE_STDBY_7X); }
|
||||
void sx127x::sleep() { writeRegister(REG_OP_MODE_7X, MODE_LONG_RANGE_MODE_7X | MODE_SLEEP_7X); }
|
||||
uint8_t sx127x::modemStatus() { return readRegister(REG_MODEM_STAT_7X); }
|
||||
void sx127x::setSyncWord(uint8_t sw) { writeRegister(REG_SYNC_WORD_7X, sw); }
|
||||
@ -168,7 +168,7 @@ int sx127x::begin(long frequency) {
|
||||
enableCrc();
|
||||
setTxPower(2);
|
||||
|
||||
idle();
|
||||
standby();
|
||||
|
||||
return 1;
|
||||
}
|
||||
@ -180,7 +180,7 @@ void sx127x::end() {
|
||||
}
|
||||
|
||||
int sx127x::beginPacket(int implicitHeader) {
|
||||
idle();
|
||||
standby();
|
||||
|
||||
if (implicitHeader) {
|
||||
implicitHeaderMode();
|
||||
|
Loading…
Reference in New Issue
Block a user