diff --git a/Config.h b/Config.h index 312db43..570bf4a 100644 --- a/Config.h +++ b/Config.h @@ -4,7 +4,7 @@ #define CONFIG_H #define MAJ_VERS 0x01 - #define MIN_VERS 0x14 + #define MIN_VERS 0x15 #define PLATFORM_AVR 0x90 #define PLATFORM_ESP32 0x80 @@ -45,8 +45,6 @@ const int pin_led_rx = 12; const int pin_led_tx = 13; - const long serial_baudrate = 115200; - #define CONFIG_UART_BUFFER_SIZE 6144 #define CONFIG_QUEUE_SIZE 6144 #define CONFIG_QUEUE_MAX_LENGTH 250 @@ -61,8 +59,6 @@ const int pin_led_rx = 12; const int pin_led_tx = 13; - const long serial_baudrate = 115200; - #define CONFIG_UART_BUFFER_SIZE 2048 #define CONFIG_QUEUE_SIZE 2048 #define CONFIG_QUEUE_MAX_LENGTH 80 @@ -77,8 +73,6 @@ const int pin_led_rx = 2; const int pin_led_tx = 4; - const long serial_baudrate = 921600; - #define CONFIG_UART_BUFFER_SIZE 6144 #define CONFIG_QUEUE_SIZE 6144 #define CONFIG_QUEUE_MAX_LENGTH 250 @@ -90,6 +84,7 @@ #define eeprom_addr(a) (a+EEPROM_OFFSET) // MCU independent configuration parameters + const long serial_baudrate = 115200; const int lora_rx_turnaround_ms = 50; // SX1276 RSSI offset to get dBm value from diff --git a/RNode_Firmware.ino b/RNode_Firmware.ino index c5a5f18..c5a86ed 100644 --- a/RNode_Firmware.ino +++ b/RNode_Firmware.ino @@ -21,6 +21,14 @@ volatile bool serial_buffering = false; char sbuf[128]; +#if MCU_VARIANT == MCU_ESP32 + #include "soc/rtc_wdt.h" + #define ISR_VECT IRAM_ATTR + bool packet_ready = false; +#else + #define ISR_VECT +#endif + void setup() { #if MCU_VARIANT == MCU_ESP32 delay(500); @@ -62,9 +70,14 @@ void setup() { LoRa.setPins(pin_cs, pin_reset, pin_dio); #if MCU_VARIANT == MCU_ESP32 - radio_locked = true; - radio_online = false; - hw_ready = false; + // ESP32-specific initialisation + // The WDT is disabled for now. This + // should be re-enabled as soon as any + // Core0-related features are used + rtc_wdt_protect_off(); + rtc_wdt_disable(); + // rtc_wdt_set_stage(RTC_WDT_STAGE0, RTC_WDT_STAGE_ACTION_RESET_SYSTEM); + // rtc_wdt_set_time(RTC_WDT_STAGE0, 25); #endif // Validate board health, EEPROM and config @@ -79,6 +92,134 @@ void lora_receive() { } } +inline void kiss_write_packet() { + Serial.write(FEND); + Serial.write(CMD_DATA); + for (int i = 0; i < read_len; i++) { + uint8_t byte = pbuf[i]; + if (byte == FEND) { Serial.write(FESC); byte = TFEND; } + if (byte == FESC) { Serial.write(FESC); byte = TFESC; } + Serial.write(byte); + } + Serial.write(FEND); + read_len = 0; + #if MCU_VARIANT == MCU_ESP32 + packet_ready = false; + #endif +} + +void ISR_VECT receive_callback(int packet_size) { + if (!promisc) { + // The standard operating mode allows large + // packets with a payload up to 500 bytes, + // by combining two raw LoRa packets. + // We read the 1-byte header and extract + // packet sequence number and split flags + uint8_t header = LoRa.read(); packet_size--; + uint8_t sequence = packetSequence(header); + bool ready = false; + + if (isSplitPacket(header) && seq == SEQ_UNSET) { + // This is the first part of a split + // packet, so we set the seq variable + // and add the data to the buffer + read_len = 0; + seq = sequence; + + #if MCU_VARIANT != MCU_ESP32 + last_rssi = LoRa.packetRssi(); + last_snr_raw = LoRa.packetSnrRaw(); + #endif + + getPacketData(packet_size); + } else if (isSplitPacket(header) && seq == sequence) { + // This is the second part of a split + // packet, so we add it to the buffer + // and set the ready flag. + + #if MCU_VARIANT != MCU_ESP32 + last_rssi = (last_rssi+LoRa.packetRssi())/2; + last_snr_raw = (last_snr_raw+LoRa.packetSnrRaw())/2; + #endif + + getPacketData(packet_size); + seq = SEQ_UNSET; + ready = true; + } else if (isSplitPacket(header) && seq != sequence) { + // This split packet does not carry the + // same sequence id, so we must assume + // that we are seeing the first part of + // a new split packet. + read_len = 0; + seq = sequence; + + #if MCU_VARIANT != MCU_ESP32 + last_rssi = LoRa.packetRssi(); + last_snr_raw = LoRa.packetSnrRaw(); + #endif + + getPacketData(packet_size); + } else if (!isSplitPacket(header)) { + // This is not a split packet, so we + // just read it and set the ready + // flag to true. + + if (seq != SEQ_UNSET) { + // If we already had part of a split + // packet in the buffer, we clear it. + read_len = 0; + seq = SEQ_UNSET; + } + + #if MCU_VARIANT != MCU_ESP32 + last_rssi = LoRa.packetRssi(); + last_snr_raw = LoRa.packetSnrRaw(); + #endif + + getPacketData(packet_size); + ready = true; + } + + if (ready) { + #if MCU_VARIANT != MCU_ESP32 + // We first signal the RSSI of the + // recieved packet to the host. + kiss_indicate_stat_rssi(); + kiss_indicate_stat_snr(); + + // And then write the entire packet + kiss_write_packet(); + #else + packet_ready = true; + #endif + } + } else { + #if MCU_VARIANT != MCU_ESP32 + // In promiscuous mode, raw packets are + // output directly to the host + read_len = 0; + last_rssi = LoRa.packetRssi(); + last_snr_raw = LoRa.packetSnrRaw(); + getPacketData(packet_size); + + // We first signal the RSSI of the + // recieved packet to the host. + kiss_indicate_stat_rssi(); + kiss_indicate_stat_snr(); + + // And then write the entire packet + kiss_write_packet(); + + #else + // Promiscous mode is not supported on ESP32 for now + getPacketData(packet_size); + read_len = 0; + #endif + } +} + + + bool startRadio() { update_radio_lock(); if (!radio_online) { @@ -101,9 +242,7 @@ bool startRadio() { LoRa.enableCrc(); - #if MCU_VARIANT != MCU_ESP32 - LoRa.onReceive(receive_callback); - #endif + LoRa.onReceive(receive_callback); lora_receive(); @@ -140,108 +279,6 @@ void update_radio_lock() { } } -void receive_callback(int packet_size) { - if (!promisc) { - // The standard operating mode allows large - // packets with a payload up to 500 bytes, - // by combining two raw LoRa packets. - // We read the 1-byte header and extract - // packet sequence number and split flags - uint8_t header = LoRa.read(); packet_size--; - uint8_t sequence = packetSequence(header); - bool ready = false; - - if (isSplitPacket(header) && seq == SEQ_UNSET) { - // This is the first part of a split - // packet, so we set the seq variable - // and add the data to the buffer - read_len = 0; - seq = sequence; - last_rssi = LoRa.packetRssi(); - last_snr_raw = LoRa.packetSnrRaw(); - getPacketData(packet_size); - } else if (isSplitPacket(header) && seq == sequence) { - // This is the second part of a split - // packet, so we add it to the buffer - // and set the ready flag. - last_rssi = (last_rssi+LoRa.packetRssi())/2; - last_snr_raw = (last_snr_raw+LoRa.packetSnrRaw())/2; - getPacketData(packet_size); - seq = SEQ_UNSET; - ready = true; - } else if (isSplitPacket(header) && seq != sequence) { - // This split packet does not carry the - // same sequence id, so we must assume - // that we are seeing the first part of - // a new split packet. - read_len = 0; - seq = sequence; - last_rssi = LoRa.packetRssi(); - last_snr_raw = LoRa.packetSnrRaw(); - getPacketData(packet_size); - } else if (!isSplitPacket(header)) { - // This is not a split packet, so we - // just read it and set the ready - // flag to true. - - if (seq != SEQ_UNSET) { - // If we already had part of a split - // packet in the buffer, we clear it. - read_len = 0; - seq = SEQ_UNSET; - } - - last_rssi = LoRa.packetRssi(); - last_snr_raw = LoRa.packetSnrRaw(); - getPacketData(packet_size); - ready = true; - } - - if (ready) { - // We first signal the RSSI of the - // recieved packet to the host. - kiss_indicate_stat_rssi(); - kiss_indicate_stat_snr(); - - // And then write the entire packet - Serial.write(FEND); - Serial.write(CMD_DATA); - for (int i = 0; i < read_len; i++) { - uint8_t byte = pbuf[i]; - if (byte == FEND) { Serial.write(FESC); byte = TFEND; } - if (byte == FESC) { Serial.write(FESC); byte = TFESC; } - Serial.write(byte); - } - Serial.write(FEND); - read_len = 0; - } - } else { - // In promiscuous mode, raw packets are - // output directly to the host - read_len = 0; - last_rssi = LoRa.packetRssi(); - last_snr_raw = LoRa.packetSnrRaw(); - getPacketData(packet_size); - - // We first signal the RSSI of the - // recieved packet to the host. - kiss_indicate_stat_rssi(); - kiss_indicate_stat_snr(); - - // And then write the entire packet - Serial.write(FEND); - Serial.write(CMD_DATA); - for (int i = 0; i < read_len; i++) { - uint8_t byte = pbuf[i]; - if (byte == FEND) { Serial.write(FESC); byte = TFEND; } - if (byte == FESC) { Serial.write(FESC); byte = TFESC; } - Serial.write(byte); - } - Serial.write(FEND); - read_len = 0; - } -} - bool queueFull() { return (queue_height >= CONFIG_QUEUE_MAX_LENGTH || queued_bytes >= CONFIG_QUEUE_SIZE); } @@ -650,9 +687,8 @@ void loop() { checkModemStatus(); #if MCU_VARIANT == MCU_ESP32 - int packet_size = LoRa.parsePacket(); - if (packet_size) { - receive_callback(packet_size); + if (packet_ready) { + kiss_write_packet(); } #endif @@ -686,12 +722,9 @@ void loop() { #if MCU_VARIANT == MCU_ESP32 buffer_serial(); - #endif - - #if MCU_VARIANT != MCU_ESP32 - if (!fifo_isempty_locked(&serialFIFO)) serial_poll(); - #else if (!fifo_isempty(&serialFIFO)) serial_poll(); + #else + if (!fifo_isempty_locked(&serialFIFO)) serial_poll(); #endif } diff --git a/Utilities.h b/Utilities.h index ebc09b4..4c6cfdb 100644 --- a/Utilities.h +++ b/Utilities.h @@ -381,15 +381,15 @@ void kiss_indicate_mcu() { Serial.write(FEND); } -bool isSplitPacket(uint8_t header) { +inline bool isSplitPacket(uint8_t header) { return (header & FLAG_SPLIT); } -uint8_t packetSequence(uint8_t header) { +inline uint8_t packetSequence(uint8_t header) { return header >> 4; } -void getPacketData(int len) { +inline void getPacketData(int len) { while (len--) { pbuf[read_len++] = LoRa.read(); }