Clean up debug prints for PR

2024-12-28 08:59:33 -05:00 · 2024-03-11 12:35:29 -04:00 · 2024-03-11 12:35:29 -04:00 · 5c1e0f25ee
commit 5c1e0f25ee
parent 36ab438625
5 changed files with 13 additions and 78 deletions
--- a/Boards.h
+++ b/Boards.h
@ -261,14 +261,13 @@
      #define IS_ESP32S3 true
      #define HAS_DISPLAY true
      //ESP32-S3 no bluetooth classic
-      //#define HAS_BLUETOOTH true
      #define HAS_BLUETOOTH false
-      //#define HAS_BLE true
      // TODO BLE
      #define HAS_BLE false
      // Cannot run wifi and BLE at same time?
      #define HAS_CONSOLE false
      #define HAS_EEPROM true
+      // Only one LED on pin 35
      #if defined(EXTERNAL_LEDS)
        const int pin_led_rx = 35;
        const int pin_led_tx = 2;
@ -278,11 +277,12 @@
      #endif

      #define MODEM SX1262
+      // TODO TCXO?
      //#define HAS_TCXO true
      #define HAS_TCXO false
+      const int pin_tcxo_enable = -1;
      #define HAS_BUSY true
      #define DIO2_AS_RF_SWITCH true
-      const int pin_tcxo_enable = -1;

      // following pins are for the sx1262
      const int pin_cs = 8;
--- a/Display.h
+++ b/Display.h
@ -34,7 +34,6 @@
  #define SDA_OLED 4
 #elif BOARD_MODEL == BOARD_HELTEC_LORA32_V3
  #define DISP_RST 21
-  //#define DISP_RST -1
  #define DISP_ADDR 0x3C
  #define SCL_OLED 18
  #define SDA_OLED 17
@ -115,28 +114,17 @@ bool display_init() {
    #elif BOARD_MODEL == BOARD_HELTEC32_V2
      Wire.begin(SDA_OLED, SCL_OLED);
    #elif BOARD_MODEL == BOARD_HELTEC_LORA32_V3
-      Serial.println("display - 1 ");
-      // vext
+      // enable vext / pin 36
      pinMode(Vext, OUTPUT);
-      //digitalWrite(36, LOW);
      digitalWrite(Vext, LOW);
-      delay(500);
-      Serial.println("display - 2 ");
-      //Serial.print("vext ");
-      //Serial.println(Vext);
+      delay(50);
      int pin_display_en = 21;
-      //digitalWrite(pin_display_en, HIGH);
-      //delay(50);
      pinMode(pin_display_en, OUTPUT);
      digitalWrite(pin_display_en, LOW);
      delay(50);
      digitalWrite(pin_display_en, HIGH);
      delay(50);
      Wire.begin(SDA_OLED, SCL_OLED);
-      // ble debug
-      //Serial.println("Setup display pins LORA32 V3");
-      Serial.println("vext ");
-      Serial.println(Vext);
    #elif BOARD_MODEL == BOARD_LORA32_V1_0
      int pin_display_en = 16;
      digitalWrite(pin_display_en, LOW);
@ -180,7 +168,9 @@ bool display_init() {
        display.setRotation(1);
      #elif BOARD_MODEL == BOARD_HELTEC_LORA32_V3
        disp_mode = DISP_MODE_PORTRAIT;
+        // Antenna conx up
        display.setRotation(1);
+        // USB-C up
        //display.setRotation(3);
      #else
        disp_mode = DISP_MODE_PORTRAIT;
@ -198,14 +188,7 @@ bool display_init() {
      disp_area.cp437(true);
      display.cp437(true);

-      Serial.print("(1)display int= ");
-      Serial.println(display_intensity);
      display_intensity = EEPROM.read(eeprom_addr(ADDR_CONF_DINT));
-      Serial.print("(2)display int= ");
-      Serial.println(display_intensity);
-      display_intensity = 100;
-      Serial.print("(2)display int= ");
-      Serial.println(display_intensity);

      return true;
    }
@ -566,8 +549,6 @@ void draw_disp_area() {
 }

 void update_disp_area() {
-  // ble debug
-  Serial.println("...update disp area...");
  draw_disp_area();
  display.drawBitmap(p_ad_x, p_ad_y, disp_area.getBuffer(), disp_area.width(), disp_area.height(), SSD1306_WHITE, SSD1306_BLACK);
  if (disp_mode == DISP_MODE_LANDSCAPE) {
--- a/2
+++ b/2
@ -94,7 +94,7 @@ firmware-heltec32_v2_extled:
 	arduino-cli compile --fqbn esp32:esp32:heltec_wifi_lora_32_V2 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x38\" \"-DEXTERNAL_LEDS=true\""

 firmware-heltec32_v3:
-	arduino-cli compile --fqbn esp32:esp32:heltec_wifi_lora_32_V3 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x39\""
+	arduino-cli compile --fqbn esp32:esp32:heltec_wifi_lora_32_V3 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x3a\""

 firmware-rnode_ng_20:
 	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x40\""
--- a/RNode_Firmware.ino
+++ b/RNode_Firmware.ino
@ -143,9 +143,6 @@ void setup() {
      eeprom_update(eeprom_addr(ADDR_CONF_DINT), 0xFF);
    }
    disp_ready = display_init();
-      // ble debug
-    Serial.print("disp ready = ");
-    Serial.println(disp_ready);
    update_display();
  #endif

@ -383,10 +380,6 @@ void stopRadio() {
 }

 void update_radio_lock() {
-      // ble debug
-    //static char lock[40];
-    //sprintf(lock, "lock chk %d %d %x %d", lora_freq, lora_bw, lora_txp, lora_sf);
-    //Serial.println(lock);
  if (lora_freq != 0 && lora_bw != 0 && lora_txp != 0xFF && lora_sf != 0) {
    radio_locked = false;
  } else {
@ -612,9 +605,6 @@ void serialCallback(uint8_t sbyte) {
            lora_freq = freq;
            if (op_mode == MODE_HOST) setFrequency();
            kiss_indicate_frequency();
-      // ble debug
-            //Serial.print("freq ");
-            //Serial.println(lora_freq);
          }
        }
    } else if (command == CMD_BANDWIDTH) {
@ -700,8 +690,6 @@ void serialCallback(uint8_t sbyte) {
      } else if (sbyte == 0x01) {
        startRadio();
        kiss_indicate_radiostate();
-      // ble debug
-        //Serial.println("start radio");
      }
    } else if (command == CMD_ST_ALOCK) {
      if (sbyte == FESC) {
@ -1075,11 +1063,6 @@ void validate_status() {
      uint8_t F_WDR = 0x01;
  #endif

-        // ble debug
-        Serial.print("hw_ready ");
-        Serial.print(hw_ready);
-        Serial.print(" device init done ");
-        Serial.println(device_init_done);
  if (hw_ready || device_init_done) {
    hw_ready = false;
    Serial.write("Error, invalid hardware check state\r\n");
@ -1110,32 +1093,22 @@ void validate_status() {
  }

  if (boot_vector == START_FROM_BOOTLOADER || boot_vector == START_FROM_POWERON) {
-    //if (eeprom_lock_set()) {
-    if (1) {
+    if (eeprom_lock_set()) {
      if (eeprom_product_valid() && eeprom_model_valid() && eeprom_hwrev_valid()) {
        if (eeprom_checksum_valid()) {
          eeprom_ok = true;
          if (modem_installed) {
            #if PLATFORM == PLATFORM_ESP32
              if (device_init()) {
-                // ble debug
-                Serial.println("hw ready 1");
                hw_ready = true;
              } else {
                hw_ready = false;
-                // ble debug
-                Serial.println("hw ! ready 1");
              }
            #else
              hw_ready = true;
-                // ble debug
-                Serial.println("hw ready 2");
            #endif
          } else {
            hw_ready = false;
-            // ble debug
-            Serial.println("hw ! ready 3");
-            Serial.write("No valid radio module found\r\n");
            #if HAS_DISPLAY
              if (disp_ready) {
                device_init_done = true;
@ -1148,14 +1121,9 @@ void validate_status() {
            eeprom_conf_load();
            op_mode = MODE_TNC;
            startRadio();
-            // ble debug
-            Serial.println("hw ready - start radio");
-
          }
        } else {
          hw_ready = false;
-          // ble debug
-          Serial.println("hw ! ready 4");
          #if HAS_DISPLAY
            if (disp_ready) {
              device_init_done = true;
@ -1165,26 +1133,15 @@ void validate_status() {
        }
      } else {
        hw_ready = false;
-        // ble debug
-        Serial.println("hw ! ready 5  - override  - TODO");
-        
-        //  override eeprom flags - ble debug
-        hw_ready = true;
-        //
-
        #if HAS_DISPLAY
          if (disp_ready) {
            device_init_done = true;
            update_display();
-          // ble debug
-            Serial.println("update display called");
          }
        #endif
      }
    } else {
      hw_ready = false;
-      // ble debug
-      Serial.println("hw ! ready 6");
      #if HAS_DISPLAY
        if (disp_ready) {
          device_init_done = true;
@ -1194,9 +1151,6 @@ void validate_status() {
    }
  } else {
    hw_ready = false;
-      // ble debug
-    Serial.println("hw ! ready 7 - bad boot vector");
-    Serial.write("Error, incorrect boot vector\r\n");
    #if HAS_DISPLAY
      if (disp_ready) {
        device_init_done = true;
--- a/Utilities.h
+++ b/Utilities.h
@ -60,12 +60,12 @@ sx128x *LoRa = &sx128x_modem;
 	#include "Device.h"
 #endif
 #if MCU_VARIANT == MCU_ESP32
-	//#if BOARD_MODEL != BOARD_RNODE_NG_22 && BOARD_MODEL != BOARD_HELTEC_LORA32_V3
-	//  #include "soc/rtc_wdt.h"
-  //#else
+  #if BOARD_MODEL == BOARD_HELTEC_LORA32_V3
    //https://github.com/espressif/esp-idf/issues/8855
    #include "hal/wdt_hal.h"
-	//#endif
+  #elif BOARD_MODEL != BOARD_RNODE_NG_22
+	  #include "soc/rtc_wdt.h"
+	#endif
  #define ISR_VECT IRAM_ATTR
 #else
  #define ISR_VECT