Merge pull request #35 from mrmx/lora32_v10

Initial support for TTGO LORA SX1278 ESP32 0.96 OLED 32Mbit (4MB) 433Mhz v1.0

Config.h

@@ -35,6 +35,7 @@
 	#define BOARD_GENERIC_ESP32 0x35
 	#define BOARD_LORA32_V2_0   0x36
 	#define BOARD_LORA32_V2_1   0x37
+	#define BOARD_LORA32_V1_0   0x39
 	#define BOARD_HELTEC32_V2   0x38
 	#define BOARD_RNODE_NG_20   0x40
 	#define BOARD_RNODE_NG_21   0x41
@@ -156,6 +157,20 @@
 			const int pin_led_rx = 14;
 			const int pin_led_tx = 32;
 			#define HAS_BLUETOOTH true
+            #define HAS_CONSOLE true
+		#elif BOARD_MODEL == BOARD_LORA32_V1_0
+			const int pin_cs = 18;
+			const int pin_reset = 14;
+			const int pin_dio = 26;
+			#if defined(EXTERNAL_LEDS)
+				const int pin_led_rx = 25;
+				const int pin_led_tx = 2;
+			#else
+				const int pin_led_rx = 2;
+				const int pin_led_tx = 2;
+			#endif
+            #define HAS_DISPLAY true
+            #define HAS_BLUETOOTH true
             #define HAS_CONSOLE true
 		#elif BOARD_MODEL == BOARD_LORA32_V2_0
 			const int pin_cs = 18;

Display.h

@@ -26,7 +26,7 @@
   #define DISP_RST 13
   #define DISP_ADDR 0x3D
   // #define DISP_ADDR 0x3C
-#elif BOARD_MODEL == BOARD_HELTEC32_V2
+#elif BOARD_MODEL == BOARD_HELTEC32_V2 || BOARD_MODEL == BOARD_LORA32_V1_0
   #define DISP_RST 16
   #define DISP_ADDR 0x3C
   #define SCL_OLED 15
@@ -87,7 +87,7 @@ void set_contrast(Adafruit_SSD1306 *display, uint8_t contrast) {
 
 bool display_init() {
   #if HAS_DISPLAY
-    #if BOARD_MODEL == BOARD_RNODE_NG_20 || BOARD_MODEL == BOARD_LORA32_V2_0
+    #if BOARD_MODEL == BOARD_RNODE_NG_20 || BOARD_MODEL == BOARD_LORA32_V2_0 || BOARD_LORA32_V1_0
       int pin_display_en = 16;
       digitalWrite(pin_display_en, LOW);
       delay(50);
@@ -96,6 +96,10 @@ bool display_init() {
       Wire.begin(SDA_OLED, SCL_OLED);
     #endif
     
+    #if BOARD_MODEL == BOARD_LORA32_V1_0
+      Wire.begin(SDA_OLED, SCL_OLED);
+    #endif
+    
     if(!display.begin(SSD1306_SWITCHCAPVCC, DISP_ADDR)) {
       return false;
     } else {
@@ -106,6 +110,9 @@ bool display_init() {
       #elif BOARD_MODEL == BOARD_RNODE_NG_21
         disp_mode = DISP_MODE_PORTRAIT;
         display.setRotation(3);
+      #elif BOARD_MODEL == BOARD_LORA32_V1_0
+        disp_mode = DISP_MODE_PORTRAIT;
+        display.setRotation(3);
       #elif BOARD_MODEL == BOARD_LORA32_V2_0
         disp_mode = DISP_MODE_PORTRAIT;
         display.setRotation(3);

Makefile

@@ -58,6 +58,12 @@ firmware-mega2560:
 firmware-tbeam:
 	arduino-cli compile --fqbn esp32:esp32:t-beam -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x33\""
 
+firmware-lora32_v10:
+	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x39\""
+
+firmware-lora32_v10_extled:
+	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x38\" \"-DEXTERNAL_LEDS=true\""
+
 firmware-lora32_v20:
 	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x36\" \"-DEXTERNAL_LEDS=true\""
 
@@ -99,6 +105,13 @@ upload-tbeam:
 	@sleep 3
 	python ./Release/esptool/esptool.py --chip esp32 --port /dev/ttyUSB1 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
 
+upload-lora32_v10:
+	arduino-cli upload -p /dev/ttyUSB0 --fqbn esp32:esp32:ttgo-lora32
+	@sleep 1
+	rnodeconf /dev/ttyUSB0 --firmware-hash $$(./partition_hashes ./build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.bin)
+	@sleep 3
+	python ./Release/esptool/esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
+
 upload-lora32_v20:
 	arduino-cli upload -p /dev/ttyUSB1 --fqbn esp32:esp32:ttgo-lora32
 	@sleep 1
@@ -144,7 +157,7 @@ upload-featheresp32:
 
 release: release-all
 
-release-all: console-site spiffs-image release-rnode release-mega2560 release-tbeam release-lora32_v20 release-lora32_v21 release-lora32_v20_extled release-lora32_v21_extled release-featheresp32 release-genericesp32 release-heltec32_v2 release-heltec32_v2_extled release-rnode_ng_20 release-rnode_ng_21 release-hashes
+release-all: console-site spiffs-image release-rnode release-mega2560 release-tbeam release-lora32_v10 release-lora32_v20 release-lora32_v21 release-lora32_v10_extled release-lora32_v20_extled release-lora32_v21_extled release-featheresp32 release-genericesp32 release-heltec32_v2 release-heltec32_v2_extled release-rnode_ng_20 release-rnode_ng_21 release-hashes
 
 release-hashes:
 	python ./release_hashes.py > ./Release/release.json
@@ -163,6 +176,15 @@ release-tbeam:
 	zip --junk-paths ./Release/rnode_firmware_tbeam.zip ./Release/esptool/esptool.py ./Release/console_image.bin build/rnode_firmware_tbeam.boot_app0 build/rnode_firmware_tbeam.bin build/rnode_firmware_tbeam.bootloader build/rnode_firmware_tbeam.partitions
 	rm -r build
 
+release-lora32_v10:
+	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x39\""
+	cp ~/.arduino15/packages/esp32/hardware/esp32/2.0.?/tools/partitions/boot_app0.bin build/rnode_firmware_lora32v10.boot_app0
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.bin build/rnode_firmware_lora32v10.bin
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.bootloader.bin build/rnode_firmware_lora32v10.bootloader
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.partitions.bin build/rnode_firmware_lora32v10.partitions
+	zip --junk-paths ./Release/rnode_firmware_lora32v10.zip ./Release/esptool/esptool.py ./Release/console_image.bin build/rnode_firmware_lora32v10.boot_app0 build/rnode_firmware_lora32v10.bin build/rnode_firmware_lora32v10.bootloader build/rnode_firmware_lora32v10.partitions
+	rm -r build
+
 release-lora32_v20:
 	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x36\""
 	cp ~/.arduino15/packages/esp32/hardware/esp32/2.0.?/tools/partitions/boot_app0.bin build/rnode_firmware_lora32v20.boot_app0
@@ -181,6 +203,15 @@ release-lora32_v21:
 	zip --junk-paths ./Release/rnode_firmware_lora32v21.zip ./Release/esptool/esptool.py ./Release/console_image.bin build/rnode_firmware_lora32v21.boot_app0 build/rnode_firmware_lora32v21.bin build/rnode_firmware_lora32v21.bootloader build/rnode_firmware_lora32v21.partitions
 	rm -r build
 
+release-lora32_v10_extled:
+	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x38\" \"-DEXTERNAL_LEDS=true\""
+	cp ~/.arduino15/packages/esp32/hardware/esp32/2.0.?/tools/partitions/boot_app0.bin build/rnode_firmware_lora32v10.boot_app0
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.bin build/rnode_firmware_lora32v10.bin
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.bootloader.bin build/rnode_firmware_lora32v10.bootloader
+	cp build/esp32.esp32.ttgo-lora32/RNode_Firmware.ino.partitions.bin build/rnode_firmware_lora32v10.partitions
+	zip --junk-paths ./Release/rnode_firmware_lora32v10.zip ./Release/esptool/esptool.py ./Release/console_image.bin build/rnode_firmware_lora32v10.boot_app0 build/rnode_firmware_lora32v10.bin build/rnode_firmware_lora32v10.bootloader build/rnode_firmware_lora32v10.partitions
+	rm -r build
+
 release-lora32_v20_extled:
 	arduino-cli compile --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x36\" \"-DEXTERNAL_LEDS=true\""
 	cp ~/.arduino15/packages/esp32/hardware/esp32/2.0.?/tools/partitions/boot_app0.bin build/rnode_firmware_lora32v20.boot_app0

README.md

@@ -65,6 +65,7 @@ The RNode Firmware supports the following boards:
 - Handheld v2.x RNodes from [unsigned.io](https://unsigned.io/shop/product/handheld-rnode)
 - Original v1.x RNodes from [unsigned.io](https://unsigned.io/shop/product/rnode)
 - LilyGO T-Beam v1.1 devices
+- LilyGO LoRa32 v1.0 devices
 - LilyGO LoRa32 v2.0 devices
 - LilyGO LoRa32 v2.1 devices
 - Heltec LoRa32 v2 devices
@@ -79,7 +80,7 @@ The RNode Firmware supports all transceiver modules based on **Semtech SX1276**
 Support for **SX1262**, **SX1268** and **SX1280** is being implemented. Please support the project with donations if you want this faster!
 
 ## Getting Started Fast
-You can download and flash the firmware to all the supported boards using the [RNode Config Utility](https://github.com/markqvist/rnodeconfigutil). All firmware releases are now handled and installed directly through the `rnodeconf` utility, which is inclueded in the `rns` package. It can be installed via `pip`:
+You can download and flash the firmware to all the supported boards using the [RNode Config Utility](https://github.com/markqvist/rnodeconfigutil). All firmware releases are now handled and installed directly through the `rnodeconf` utility, which is included in the `rns` package. It can be installed via `pip`:
 
 ```
 # Install rnodeconf via rns package

Utilities.h

@@ -123,6 +123,18 @@ uint8_t boot_vector = 0x00;
 		void led_rx_off() {	digitalWrite(pin_led_rx, LOW); }
 		void led_tx_on()  { digitalWrite(pin_led_tx, LOW); }
 		void led_tx_off() { digitalWrite(pin_led_tx, HIGH); }
+	#elif BOARD_MODEL == BOARD_LORA32_V1_0
+		#if defined(EXTERNAL_LEDS)
+			void led_rx_on()  { digitalWrite(pin_led_rx, HIGH); }
+			void led_rx_off() {	digitalWrite(pin_led_rx, LOW); }
+			void led_tx_on()  { digitalWrite(pin_led_tx, HIGH); }
+			void led_tx_off() { digitalWrite(pin_led_tx, LOW); }
+		#else
+			void led_rx_on()  { digitalWrite(pin_led_rx, HIGH); }
+			void led_rx_off() {	digitalWrite(pin_led_rx, LOW); }
+			void led_tx_on()  { digitalWrite(pin_led_tx, HIGH); }
+			void led_tx_off() { digitalWrite(pin_led_tx, LOW); }
+		#endif
 	#elif BOARD_MODEL == BOARD_LORA32_V2_0
 		#if defined(EXTERNAL_LEDS)
 			void led_rx_on()  { digitalWrite(pin_led_rx, HIGH); }